|
|
|
Who's Online
There currently are 5884 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It was a complete manual as stated. Very good source for older product manuals. Thanks
;
Scan quality is very good. Price is very reasonable. If you're looking to purchase a copy of this manual, this is the one to get.
 ;
Perfect for my use.Could have better pictures,but otherwise perfect ;)
;
This is one of four manuals I have downloaded recently.
Purchase was very straight forward and the authorising email arrived in about 4 hours.
The quality of the scan is good. Print is clear and square to the page edges.
;
Exactly as advertized. High quality digital copy of the Nak 610 user manual. Easy download and access. Highly recommended.
English
Adjusting the Volume
On the front panel:
To increase the volume, turn MASTER VOLUME clockwise. To decrease the volume, turn it counterclockwise. � When you turn MASTER VOLUME rapidly, the volume level also changes rapidly. � When you turn MASTER VOLUME slowly, the volume level also changes slowly.
MASTER VOLUME
Listening only with headphones
1. Connect a pair of headphones to the PHONES jack on the front panel. 2. Press SPEAKERS 1 and SPEAKERS 2 to set them in the � OFF position.
+
�
CAUTION:
Be sure to turn down the volume before connecting or putting on headphones, as high volume can damage both the headphones and your hearing.
Note:
+
VOLUME
From the remote control: To increase the volume, press VOLUME +. To decrease the volume, press VOLUME �.
CAUTION:
You cannot shut off the sound through the other speakers using the SPEAKERS 1 and 2 buttons.
�
Muting the Sound
From the remote control ONLY:
Press MUTING to mute the sound through all speakers and headphones connected. �MUTING� appears on the display and the volume turns off (the volume level indicator goes off). To restore the sound, press MUTING again. � Turning MASTER VOLUME or pressing VOLUME +/� also restores the sound.
SPEAKERS
Always set the volume to the minimum before starting any source. If the volume is set at its high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.
MUTING
Note:
The volume level can be adjusted within the range of �0� (minimum) to �80� (maximum).
Selecting the Front Speakers
On the front panel ONLY:
When you have connected two pairs of the front speakers, you can select which to use. Pressing SPEAKERS 1 or SPEAKERS 2 activates the respective set of speakers.
1 2
Recording a Source
You can record any source playing through the receiver to a cassette deck (or an MD recorder) connected to the TAPE/MD jacks and the VCR connected to the VCR jacks at the same time. While recording, you can listen to the selected sound source at whatever sound level you like, without affecting the sound levels of the recording.
_ ON � OFF
� To use the speakers connected to the FRONT SPEAKERS 1 terminals, press SPEAKERS 1 to set it in the _ ON position, and press SPEAKERS 2 to set it in the � OFF position. � To use the speakers connected to the FRONT SPEAKERS 2 terminals, press SPEAKERS 2 to set it in the _ ON position, and press SPEAKERS 1 to set it in the � OFF position. � To use both sets of the speakers, press SPEAKERS 1 to set it in the _ ON position, and press SPEAKERS 2 to set it in the _ ON position. � To use neither set of the speakers, press SPEAKERS 1 and SPEAKERS 2 to set them in the � OFF position.
Note:
The output volume level, tone adjustment (see page 10), Bass Boost (see page 10) and DSP modes (see page 17) cannot affect the recording.
IMPORTANT:
Before recording, turn off the DVD MULTI playback mode.
Note:
When only one set of the speakers is connected to either the FRONT SPEAKERS 1 or 2 terminals, do not activate both pairs of the speakers. If you do, no sound comes out of the front speakers.
9
|
|
|
> |
|
