|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual was complete and of great quality. Originally a tri-lingual file, I first received only one language. After a note to owners-manuals.com, I quickly received the remaining languages... Great service, definitely worth it.
;
Thank you for providing this manual and at low cost.
The Philips scope is of excellent quality, longevity and build and had a couple of faults
when it was passed to me. Having the CCT diagrams is a blessing.
I have fixed the problems and also modded the scope to my requirements.
I have built a 24v Li-Ion pack for portable use from old but good laptop batts.
it is working beautifully and I am well pleased. Keep up the good work Guys.
 ;
manual was very helpful in learning how to propery use my washer. I could not find this manual anywhere else.
;
Awesome quality manual. You really saved my bacon with this one. Was looking for some specific information with regards to my "new" vintage VCR that didn't come with the owners manual. This site is truely a goldmine of available manuals. The quality of the scans are top notch.
Thank-you so much for this awesome manual. If you're looking for this Sony SL-HF400 owners manual, this is the one you NEED to buy. Definitely worth the money.
;
The manual was made available promptly. I is a clean scan of the original. I had no problem downloading it. The scan was well centered and cleanly formatted. It is as good a product as can be had without being the original document.
Crossover Frequency Setting
Small speakers cannot reproduce the bass sound very well. So, if you have used a small speaker for any of the front, center, and rear channels, this receiver automatically reallocates the bass elements, originally assigned to the channel for which you have connected the small speaker, to another channel (for which you have connected the large speaker). If you have selected �LARGE� for all speakers (see page 12), this function will not take effect. To use this function properly, you need to set this crossover frequency level according to the size of the small speaker connected.
Low Frequency Effect Attenuator Setting
If the bass sound is distorted while playing back a source using Dolby Digital or DTS Digital Surround, follow the procedure below.
On the front panel ONLY:
1. Press SETTING repeatedly until �LFE ATT� (Low Frequency Effect Attenuator) appears on the display.
The display changes to show the current setting.
ST SETTING
On the front panel ONLY:
1. Press SETTING repeatedly until �CROSSOVER FRQ� (Crossover Frequency) appears on the display.
The display changes to show the current setting.
T SETTING
2. Press CONTROL UP 5/DOWN � to select the low frequency effect attenuator level.
� Each time you press the button, the display changes to show the following:
CONTROL DOWN UP
0dB
10dB
2. Press CONTROL UP 5/DOWN � to select the crossover frequency level according to the size of the small speaker connected.
� Each time you press the button, the display changes to show the following:
CONTROL DOWN UP
0dB: 10dB:
Normally select this. Select this when the bass sound is distorted.
Note:
This function takes effect only when the subwoofer (LFE) signals come in, (with �SUBWOOFER� set to �YES.�)
80HZ
100HZ
120HZ
Dynamic Range Compression Setting
You can compress the dynamic range (difference between maximum sound and minimum sound) of the reproduced sound. This is useful when enjoying surround sound at night. � This function takes effect only when playing back a source using Dolby Digital.
� Use the following comments as reference when adjusting. 80HZ: 100HZ: 120HZ: Select this when the cone speaker unit built in the speaker is about 4 3 /4 inches (12 cm). Select this when the cone speaker unit built in the speaker is about 3 15 /16 inches (10 cm). Select this when the cone speaker unit built in the speaker is about 3 3 /16 inches (8 cm).
On the front panel ONLY:
Note:
Crossover frequency is not valid for the HEADPHONE mode.
1. Press SETTING repeatedly until �D_RANGE COMP� (Dynamic Range Compression) appears on the display.
T SETTING
The display changes to show the current setting.
CONTROL DOWN UP
2. Press CONTROL UP 5/DOWN � to select the appropriate item about the compression level.
� Each time you press the button, the display changes to show the following:
OFF
MID
MAX
OFF: MID: MAX:
Select this when you want to enjoy surround with its full dynamic range. (No effect applied.) Select this when you want to reduce the dynamic range a little. (Factory setting.) Select this when you want to apply the compression effect fully. (Useful at night.)
Note:
Dynamic Range Compression is not valid for the DTS Digital Surround.
13
|
|
|
> |
|
