|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Zeer duidelijke afdrukken op A4-formaat , zeer uitgebreide handleiding . Pluspunt ,zeer snelle
respons van jullie , binnen de 24h . Top !!!
;
I AM HIGHLY IMPRESSED BY THE EASE OF USE OF THIS DOWNLOAD SERVICE. INSTRUCTIONS ARE CLEAR AND SIMPLE TO FOLLOW....EVEN BY TECHNOPHOBES SUCH AS MYSELF. THE EMAILS POINT YOU IN THE RIGHT DIRECTION...ITS SO EASY PEASY. THE DOWNLOAD CHOICE OF USER MANUALS IS EXTENSIVE AND I COULD NOT FIND A CHEAPER OR MORE EFFICIENT SERVICE ON THE INTERNET. I COULD NOT HAVE MADE A BETTER CHOICE OF INFORMATION PROVIDER. SHOULD I EVER NEED ANOTHER USER MANUAL, THEN THIS IS THE FIRST CHOICE SITE. COULD NOT BE BETTER PLEASED!!!!!!!...MANY THANXES FROM JIM BURNS
;
I was impressed with the quality of service (frequent e-mails to let you know the status of your order), and the speed at which the download became available. The manual was a life saver and was not easy to track down. Thank you for such an excellent service.
;
the manual was just what i wanted it had all the revelent information required to operate the hifi .Iwould use any manual i downloaded for any item which needs a manual
;
Die gewünschte Bedienungsanleitung wurde vereinbarungsgemäß in deutsch bereitgestellt. Sie ist gut lesbar. Kein Kauderwelsch.
Danke für den Service.
English
Basic Settings
Some of the following settings are required after connecting and positioning your speakers in your listening room, while others will make operations easier.
IMPORTANT:
When using the remote control, check to see if its remote control mode selector is set to the correct position: To operate this receiver, set it to �AUDIO/TV/ VCR�
AUDIO/ TV/VCR
Changing the Source Name
When you have connected an MD recorder to the TAPE/MD jacks or the DBS tuner to the TV SOUND/DBS jacks on the rear panel, change the source name which will be shown on the display when you select the MD recorder or DBS tuner as the source.
CATV/DBS
Recording a Source
For analog-to-analog recording
You can record any analog source through the receiver to � � the cassette deck (or MD recorder) connected to the TAPE/MD jacks, � and the VCR connected to the VCR jacks � at the same time.
On the front panel ONLY:
1. When changing the source name
SOURCE SELECTOR
from �TAPE� to �MD�: � Turn SOURCE SELECTOR until �TAPE� appears. When changing the source name from �TV SOUND� to �DBS�: � Turn SOURCE SELECTOR until �TV SOUND� appears. 2. Press and hold SOURCE NAME (BASS BOOST) until �ASSGN. MD� or �ASSGN. DBS� appears on the display.
BASS BOOST
For digital-to-digital recording
You can record the currently selected digital input through the receiver to a digital recording device connected to the DIGITAL OUT terminal.
Notes:
� Analog-to-digital and digital-to-analog recordings are not possible. � The output volume level, bass boost (see page 12), SEA modes (see page 24), and DSP modes (see page 25) cannot affect the recording. � The test tone signal (see pages 29 and 30) does not come out through the DIGITAL OUT terminal.
SOURCE NAME
To change the source name to �TAPE� or �TV SOUND,� repeat the same procedure above � in step 1, select �MD� or �DBS� then press and hold SOURCE NAME (BASS BOOST).
Note:
Adjusting the Front Speaker Output Balance
If the sounds you hear from the front right and left speakers are unequal, you can adjust the speaker output balance. Before you start, remember... � There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
Without changing the source name, you can still use the connected components. However, there may be some inconvenience. � �TAPE� or �TV SOUND� will appear on the display when you select the MD recorder or DBS tuner. � You cannot use the digital input (see page 16) for the MD recorder. � You cannot use the COMPU LINK remote control system (see page 39) to operate the MD recorder.
Setting the Subwoofer Information
Register whether or not you have connected a subwoofer.
On the front panel ONLY:
1. Press BALANCE (/SURROUND) ADJUST repeatedly until �L/R BALANCE� appears on the display.
The display changes to show the current setting.
BALANCE/SURROUND ADJUST
Before you start, remember... � There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
On the front panel ONLY:
MULTI JOG
2. Turn MULTI JOG to adjust the balance.
� Turning it clockwise decreases the left channel output. � Turning it counterclockwise decreases the right channel output.
1. Press SETTING repeatedly until �SUBWOOFER� appears on the display.
The display changes to show the current setting.
SETTING
MULTI JOG
2. Turn MULTI JOG to register whether you have connected a subwoofer or not.
� As you turn it, the subwoofer setting alternates between �YES� and �NO.� YES: NO: Select this when a subwoofer is used. lights up on the display (see page 11). Select this when no subwoofer is used.
SUBWFR
13
|
|
|
> |
|
