|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
;
The owners manual for the Pioneer VSX-D603S was exactly what I needed. I received it in a timely manor and it was priced fairly. I definately will use your servise again. Thank You
;
This is a great manual. It was easy to read and very accurate. The size of the manual is small so email is no problem. I highly recommend it. The manual is very hard to find other than this website.
Signal and speaker indicators on the display � The signal indicators light up to indicate the incoming channel signals. � Only the indicators for the incoming signals light up. � The frame of the signal indicator (except for �LFE� and �S�)
lights up if the corresponding speaker is set to �LARGE� or �SMALL� (for subwoofer, �YES�). � The frames of �L� and �R� indicators always light up.
Adjusting the Volume
On the front panel:
To increase the volume, turn MASTER VOLUME clockwise. To decrease the volume, turn it counterclockwise. � When you turn MASTER VOLUME rapidly, the volume level also changes rapidly. � When you turn MASTER VOLUME slowly, the volume level also changes slowly.
MASTER VOLUME � +
L
C
R
SUBWFR LFE LS
L:
S
RS
R:
C: LS: RS: S: LFE:
� When digital input is selected: Lights up when the left channel signal comes in. � When analog input is selected: Always lights up. � When digital input is selected: Lights up when the right channel signal comes in. � When analog input is selected: Always lights up. Lights up when the center channel signal comes in. Lights up when the left rear channel signal comes in. Lights up when the right rear channel signal comes in. Lights up when the monaural rear channel signal comes in. Lights up when the LFE channel signal comes in.
From the remote control: To increase the volume, press VOLUME +. To decrease the volume, press VOLUME �.
CAUTION:
VOLUME
Always set the volume to the minimum before starting any source. If the volume is set at its high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.
Note:
The volume level can be adjusted within the range of �0� (minimum) to �90� (maximum).
Notes:
� When �SUBWOOFER� is set to �YES,� SUBWFR lights up. � When you select �DVD MULTI,� all the signal indicators except �S� light up.
Selecting the Front Speakers
On the front panel ONLY:
When you have connected two pairs of the front speakers, you can select which to use. Press SPEAKERS 1 or SPEAKERS 2 to select
SPEAKERS
Selecting different sources for picture and sound
You can watch picture from a video component while listening to sound from another component.
On the front panel:
1. Press SOUND SELECT (INPUT ATT.) briefly while viewing the picture from a video component such as the VCR or DVD player, etc.
�SOUND SELECT� appears on the display.
SOUND SELECT
the speaker to use. � Each time you press the button, the lamp on the respective button turns on and off. When the lamp on either button lights up, the respective speakers are activated.
1
2
INPUT ATT.
Note:
If you use any of the DSP modes other than the 3D-PHONIC modes with both front speakers activated, the speakers connected to the FRONT SPEAKERS 2 terminals are deactivated.
2. Turn SOURCE SELECTOR to select the sound (except the TV sound), while the indication of the above step is still on the display.
SOURCE SELECTOR
From the remote control: Press one of the audio source selecting buttons (CD, TAPE/MD, PHONO, FM/AM, TV/DBS*), while viewing the picture from a video component such as the VCR or DVD player, etc. Notes:
� Once you have selected a video source, pictures of the selected source are sent to the TV until you select another video source. * The TV/DBS button only works for selecting �DBS� as the source but not for selecting �TV SOUND.� When you use the DBS tuner, change the source name correctly (see page 13).
11
|
|
|
> |
|
