|
Who's Online
There currently are 4919 guests and 2 members online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Very good quality original datasheet!I like this amazing website!!!!!!
;
Excellent just what I needed to replace the electrolytic caps and make this old gem a beauty again. Was as scan of the original photocopied service manual.
;
It was helpful to get schematic with waveforms in important points and lot of service information. Manual is good quality, fast delivered. Of course it is hardcopy of paper one with all its disadvantages.
;
I want to give you a real heads-up for your desire to enable such people as I to acquire the information I need to maintain the older types of equipment such as this Akai HXA351W. You do a swell job with all the processes you have to perform so I can have a legible, thus usable
document which does not send me crazy trying to figure out the blurry text of a bad copy.
Very well done, Thomas.
;
This manual is very well presented and after printing out looks about as close to an original as I think you can get. The quality is second to none.
The content of the manual is comprehensive and I think it would be well suited to an audio repair professional which I'm not but I did find it very informative and helpful.
The cost of the manual is more than covered by the money I'll save when I change the keep memory battery now I have the relavant info.
Very pleased with my purchase and can recommend it wholeheartedly as I can other manuals I've downloaded from this site.
Regards
Limey Alex
RXD-803/803E/853/853E/A83
ADJUSTMENT
CD player adjustment
No. ITEM INPUT SETTINGS OUTPUT SETTINGS PLAYER SETTINGS ALIGNMENT POINTS ALIGN FOR FIG.
1. While pressing the "DISC 3" key, turn the power on to enter the test mode. 2. Load a disc on disc 1 tray. LASER CURRENT CHECK Test disc Type 4 Connect the DC voltmeter to CN6(pin1 and 2) on X32. Press the PLAY/PAUSE key, then confirm that the display is 03 or 05.
1
�
0.5±0.2V
Note: Type 4 disc : SONY YEDS-18 Test Disc or equivalent. LPF: Around 47 k�+ 390 pF or so. Step 1~4 are in Test Mode.
Cassette Deck adjustment
NO. I ITEM INPUT SETTING OUTPUT CASSETTE TAPE SETTING DECK SETTING ALIGNMENT POINTS ALIGN FOR FIG. 0dBs = 0.775V Recording head, erase head, capstan pinch roller Demagnetize the REC / PLAY head with the head eraser. Clean the REC / PLAY head, erase head, capstan and pinch roller using a cotton swab slightly damped with alcohol.
Cassette mechanism unit (Adjustment of the REC / PLAY head)
(1)
Demagnetization and cleaning
{
Power : OFF Demagnetization, cleaning, PLAY
(2)
Azimuth of the REC / PLAY head
SCC-1727 TCC-153 MTT-114 10kHz, -10dB
(B)
PLAY
RVS
Adjust the output to maximum and adjust the azimuth adjustment screw for the Lissajours waveform pattern of FWD the oscilloscope to become close to a 45� straight line.
II
PC BOARD ADJUSTMENT TCC-110 MTT-111 SCC-1727 3kHZ
(1)
TAPE SPEED (NORMAL)
(B)
PLAY
VR5
Adjust the tape speed so that 3kHz is obtained at the center of the tape.
III
PC board adjustment. MTT-150 400Hz (1) PLAYBACK LEVEL MTT-256, SCC-1727 315Hz MTT-256U, TCC-120 315 Hz (A) Adjust the AG for the output of the DECK to become 12.5KHz -20dBs. 400Hz/12.5kHz (AC-224) (B) PLAY VR 3 (L) VR 4 (R) Adjust the playback output to -2.5dBs.
Adjust the playback output to -5.5dBs.
Adjust the playback output to -1.5dBs.
(2)
BIAS CURRENT
(B)
REC PLAY
VR 1 (L) VR 2 (R)
Record 400Hz and 12.5kHz alternately, and adjust the bias current adjustment potentiometer for the playback levels to become the same.
Measurement Equipment Connections
+
ANTENNA AM
R L FRONT SPEAKERS (6-16 )
GND
FM 75
SUPER WOOFER PRE OUT
6CH. INPUT
L
CENTER SPEAKER ( 6-16 ) +
R
FRONT
SURROUND
L R
CENTER SUB WOOFER
AC voltmeter
SURROUND SPEAKERS (12-16 )
AG
X13, CN1
L-PLAY 31 30 R-PLAY GND 29 28
DIGITAL OUT OPTICAL
Oscilloscope
AC voltmeter Frequency counter
AC 110120V~
AC 220240V~
(A)
(B)
11
|
|
|
> |
|