|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I found my Clarion VRX8370R in the Camper I bought and I wasn't able for month to understand it.
The Owner Manual was perfect and just what I was searching for.
Thank you.
Leonardo
;
Very good copy of Manual, clear and easy to print off, arrived very promptly and reasonably priced.
Thanks, I will use you again.
;
Zeer duidelijke afdrukken op A4-formaat , zeer uitgebreide handleiding . Pluspunt ,zeer snelle
respons van jullie , binnen de 24h . Top !!!
;
I AM HIGHLY IMPRESSED BY THE EASE OF USE OF THIS DOWNLOAD SERVICE. INSTRUCTIONS ARE CLEAR AND SIMPLE TO FOLLOW....EVEN BY TECHNOPHOBES SUCH AS MYSELF. THE EMAILS POINT YOU IN THE RIGHT DIRECTION...ITS SO EASY PEASY. THE DOWNLOAD CHOICE OF USER MANUALS IS EXTENSIVE AND I COULD NOT FIND A CHEAPER OR MORE EFFICIENT SERVICE ON THE INTERNET. I COULD NOT HAVE MADE A BETTER CHOICE OF INFORMATION PROVIDER. SHOULD I EVER NEED ANOTHER USER MANUAL, THEN THIS IS THE FIRST CHOICE SITE. COULD NOT BE BETTER PLEASED!!!!!!!...MANY THANXES FROM JIM BURNS
;
I was impressed with the quality of service (frequent e-mails to let you know the status of your order), and the speed at which the download became available. The manual was a life saver and was not easy to track down. Thank you for such an excellent service.
Guided Tour - Rear Panel
1 2 4
OUTPUT
PUSH TO RESET 20A / 250V
BRIDGE (8�~16�) BALANCED 0dBm
PUSH
7
INPUT
PUSH
1
BALANCED 0dBm
ENGLISH
12 A M P
TRS BALANCED
(4�~8�)
(4�~8�)
�TIP=HOT �RING=COLD �SLEEVE=GND XLR BALANCED �3=COLD �2=HOT �1=GND
(4�~8�)
(4�~8�)
~AC INPUT 120V 60Hz, 770W
BRIDGED STEREO
PARALLEL
CH 2
CH 1
CH 2
CH 1
3
5
6
8
1: Fan - This variable-speed fan provides vital cooling to your S700 / S1000 (the hotter the amp gets, the faster the fan blows!). Make sure that both the front and rear panels are kept free of all obstructions and that cool, fresh air is accessible at all times. Also, try to ensure that the S700 / S1000 is used in a dust-free environment. 2: Circuit Breaker - This circuit breaker will trip if there is a fault with the mains voltage or if maximum output is exceeded (very highly distorted). Push it in (once only!) to restart the amplifier. 3: AC input - Connect the supplied heavy-gauge 3-pin �IEC� power cable here. 4: Banana output connectors - Use these to connect each channel of the S700 / S1000 to 4- or 8-ohm loudspeakers. Be sure to connect the loudspeaker correctly, with the red (+) terminal normally connected to the positive input of the speaker and the black (ground) terminal normally connected to the negative input of the speaker. See page 7 in this manual for more information about Bridged mode and pages 8 and 9 in this manual for full speaker connection instructions. 5: Speakon� output connectors - Alternatively, you can use these to connect each channel of the S700 / S1000 to 4- or 8-ohm loudspeakers. See page 7 in this manual for more information about Bridged mode and pages 8 and 9 in this manual for full Speakon� connector wiring and interconnection instructions. 6: Bridged / Stereo / Parallel switch - For normal operation, place this three-way switch in its center (�STEREO�) position. When placed in its right (�PARALLEL�) position, the signal arriving at the Channel 1 input only is routed to the power amplifiers of both Channel 1 and Channel 2 (the Channel 2 input is ignored), with each power amplifier delivering 350 watts into 4 ohms (in the case of the S700) or 500 watts into 4 ohms (in the case of the S1000). When placed in its left (�BRIDGED�) position, the signal arriving at the Channel 1 input only is again routed to both power amplifiers (again, the Channel 2 input is ignored), but the two power amplifiers are bridged together, providing a full 700 watts of power into 8 ohms (in the case of the S700) or a full 1000 watts of power into 8 ohms (in the case of the S1000). For more information, see the �Bridged and Parallel Modes� section on page 7 in this manual and the �S700 / S1000 Connections� section on pages 8 -9 in this manual. WARNING: Due to the extremely high power output of the S700 / S1000 when used in Bridged mode, be sure to use only loudspeakers sufficiently rated to handle the resultant wattage (in Bridged mode, these must be 8-ohm speakers). 7: Input connectors - Connect incoming signal to these electronically balanced Combination connectors, using either XLR or 1/4" TRS (Tip/Ring/Sleeve) plugs, wired as follows: Pin 2 (or Tip) hot, Pin 3 (or Ring) cold, and Pin 1 (or Sleeve) ground. We recommend the use of balanced three-conductor cabling wherever possible (unbalanced two-conductor 1/4" plugs can also be inserted into these inputs, but you�ll get better signal quality and less outside noise and hum if you use balanced lines). The S700 / S1000 accepts input levels of any strength but needs at least 0 dBu to achieve maximum power. Stereo signals should be connected to both the Channel 1 and Channel 2 input jacks; however, when operating the S700 / S1000 in Bridged or Parallel modes, use the Channel 1 input jack only. See page 7 in this manual for more information about Parallel mode and pages 8 and 9 in this manual for full interconnection instructions. 8: Link connectors - These XLR connectors provide unity gain outputs, allowing the S700 / S1000 to be daisy-chained to additional power amplifiers. Wiring is as follows: Pin 2 hot, Pin 3 cold, Pin 1 ground. See page 9 in this manual for more information. 4
|
|
|
> |
|
