|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Good copy and great customer service! There was some confusion with my order and it was resolved promptly!
;
Having bought a pre-owned Sony FM stereo tuner through eBay, it came without any manuals. It soon became clear that to get the best from this excellent tuner I needed a decent manual because much of the operation was not intuitive to a newboy to hi fi like me. I managed to download the official Sony multi-lingual manual from Owner-Manuals.com with no problem at all - a really quick and easy service. I'm very glad I did because I found out all the operations of the tuner and was then able to not only set it up quickly but also to get much more from it that poke-and-hope trialling would ever achieve. In my book $4.99 very well spent.
;
This manual is immaculate in it's accuracy. Everything is written very clearly and easy to understand. Written by a professional who wants to convey a clear and easy to understand message!!
;
This Manual (as downloaded) is both informative and comprehensive and has proved to be extremely useful. thoroughly recommended.
;
everything is ok, thank you very much! Product is good, no problems with download!
The S1500 / S2000 Protection Circuitry
As noted in the �Guided Tour� section of this manual, the S1500 / S2000 frontpanel Protection LED indicates the activity of the relay speaker connection circuitry. When the Protection LED is lit, this circuitry is active, and all connected speakers are muted (provided with 0 volts DC), thus protecting them and preventing any audible �thump� from occurring. The following conditions will cause the Protection LED to go on: � Initial power-up: For approximately five seconds after initial power-up, the protection circuitry is activated and the speaker output is muted. If everything is operating normally, you will hear an audible click at the conclusion of this brief period, as the protection circuitry is deactivated and the S1500 / S2000 begins delivering signal to connected speakers (at which point you�ll hear a click). It is normal for the Protection LED to fade gradually after the amplifier is powered off. WARNING: If the Protection LED fails to go out (and you fail to hear the accompanying audible click) approximately five seconds after power-up, turn the S1500 / S2000 off immediately and check all external devices and wiring for possible shorts or other defects. � Overheating: A temperature sensing device in the S1500 / S2000 will cause the protection circuitry to be activated (and the Protection LED to go on) whenever the operating temperature of the unit rises above a safe level. To guard against this problem, make sure the S1500 / S2000 receives adequate ventilation on all sides and that both the front and rear panels are unobstructed. � Severe overcurrent conditions: This occurs whenever the signal being input to the S1500 / S2000 rises to a level above 20% THD (Total Harmonic Distortion). � Shorted speaker cables: This will occur if, due to faulty wiring, the hot and ground signals being output by the S1500 / S2000 short one another. � Output impedance drops below 2 ohms: This can occur if the S1500 / S2000 is connected to inappropriate speaker systems (see the �Setting Up and Using Your S1500 / S2000� section on page 5 in this manual for more information). � DC voltage detected at speaker output: The most likely cause of this is an internal failure.
PROTECTION
In general, any time the Protection LED lights up (other than during the approximately five seconds following initial power-up), there is reason to be concerned. If this occurs, turn the S1500 / S2000 off immediately and carefully check all wiring and external devices in order to locate and correct the condition that caused the LED to light up in the first place. For further assistance, contact your local Samson dealer. If purchased in the United States, you can call Samson Technical Support (1-800-372-6766) between 9 AM and 5 PM EST.
6
|
|
|
> |
|
