|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
Installation of Self-Adhesive Rubber Pads: If the S36AW is to be placed on a surface (such as a table top or shelf) rather than being wallmounted, the enclosed selfadhesive rubber pads are to be attached to the bottom of the speaker cabinet in their designated recessed locations. If the S36AW is to be wall-mounted, then the four self-adhesive rubber pads should be attached to the back
of the speaker, as shown in the bottom right diagram. When angle-mounting the S36AW, only two of the rubber pads are required, and they need to be installed on the back of the loudspeaker, near the lower edge, so that they are located between the S36AW back and the mounting surface. Please see the enclosed installation template for more details.
PLACE RUBBER PADS HERE PADS GO HERE
For tabletop or shelf placement
KEYHOLES FOR MOUNTING HARDWARE
For wall-mounting
SPEAKER CONNECTIONS
CONNECTION TIPS
important to connect both speakers identically: (+) on the speaker to (+) on the amplifier and (�) on the speaker to (�) on the amplifier. Wiring �out of phase� results in thin sound, weak bass and a poor stereo image. With the advent of multichannel surround sound systems, connecting all of the speakers in your system with the correct polarity remains
�
RIGHT LEFT
+ �+ � +
�
+
Speaker Outputs
Speakers and electronics terminals have corresponding (+) and (�) terminals. It is
equally important in order to preserve the proper ambience and directionality of the program material.
TROUBLESHOOTING
If there is no sound from any of the speakers: � Check that receiver/ amplifier is on and that a source is playing. � Review proper operation of your receiver/amplifier. � Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. If the system plays at low volumes but shuts off as volume is increased: � Check all wires and connections between receiver/ amplifier and speakers. � Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. � If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier. If there is no sound coming from one speaker: � Check the �Balance� control on your receiver/ amplifier. � Check all wires and connections between receiver/amplifier and speakers. � Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured.
Declaration of Conformity
We, Harman Consumer International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility, that the loudspeaker described in this owner s manual is in compliance with technical standards: EN 50081-1:1992 EN 50082-1:1992
Luc E. Godard Harman Consumer International Chateau-du-Loir, France. 3/01
|
|
|
> |
|
