|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Fast service, document is OK. Thanks! Searched for it long time.
 ;
I was very pleased with the manual I got for my amateur (ham) radio. Without it I could not figure out how to input and/or change the P/L setting on my radio. It drove me nuts as the radio was essentially useless. That all changed when my manual came. Then it took only minutes and I was done. Now my radio works fine. This is an exceptionally good resource as it's a very easy and user friendly download. Thank you very much! Dziękujemy za!
;
It answered my question, which was how to load the paper. I did notice that the very end of the manual was not visible.
;
The product manual I received was exactly what I was looking for, delivered painlessly at a very fair price. I can't ask for any more than that.
;
Very well done!!!!! congratulations. It was a bit longer than usual the wiating time even if it was on time (in 24 hours).
The radio: manual tuning
The radio: preset tuning
Remote control only
There are two methods of pre-setting stations. Automatic presetting : All the stations the tuner can receive are preset. Manual presetting : You can select the stations to preset and the order they are preset in. Up to 15 stations each can be set in the FM and AM bands.
1 3
2
Numbered buttons
1 Press [TUNER/BAND] to select band.
The unit comes on. Every time you press the button: FM � AM
PLAY MODE TUNER
PROGRAM
2 Press [PLAY MODE] on the remote control to select
�MANUAL�.
Every time you press the button: MANUAL � PRESET Preparation: Press [TUNER] to select �FM� or �AM�.
3 Hold down [g/REW/3] or [4/FF/f] for a moment
to search for a station.
The frequency stops when it finds a clear station. To stop during the process, press [g/REW/3] or [4/FF/f]. Under excessive interference, a station may not be found. Press [g/REW/3] or [4/FF/f] repeatedly to tune step-bystep. �TUNED� is displayed when a radio station is tuned. �ST� is displayed when a stereo FM broadcast is being received.
Automatic presetting
Do the following once each for FM and AM. Preparation: Tune to the frequency where pre-setting is to begin.
Hold down [PROGRAM] until the frequency changes.
The tuner presets all the stations it can receive into the channels in ascending order. When finished, the last station memorized is tuned in.
Manual presetting If noise is excessive in FM
Remote control only Pre-set the stations one at a time. 1 Press [PROGRAM] then press [g/REW/3 ] [4/ FF/f] to tune to the desired station. 2 Press [PROGRAM] then press [g/REW/3 ] [4/ FF/f] to select a channel. 3 Press [PROGRAM]. or or
Hold down [PLAY MODE] to display �MONO�.
Monaural sound is selected and noise reduces when reception is weak. Hold down [PLAY MODE] again to cancel the mode. �MONO� is also cancelled if the frequency is changed.
To receive FM broadcasts allocated in 0.1MHz steps
Main unit only Hold down [TUNER/BAND]. The display changes in a few seconds to show the current minimum FM frequency. Continue to hold down the button until the minimum frequency changes. The step is changed. Changing the step erases all preset stations. Repeat the above to change the step back.
The station occupying a channel is erased if another station is preset in that channel.
Selecting channels
Press the numbered buttons to select the channel.
To enter channel 10 or over, press [�10], then the two digits. OR
� �
Notes After changing the �allocation� setting, the frequencies you previously preset in the memory will be cleared. Sound is momentarily interrupted if you load/unload tapes while listening to an AM broadcast.
1 Press [PLAY MODE] to select �PRESET�. 2 Press [g/REW/3] or [4/FF/f] to select the channel.
7
RQT6351
Recording Cassette deck operations
|
|
|
> |
|
