|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
perfect! you just sent to me the copy in Italian witout even my specification!!!! so you are really smart cooperative and efficient. To my opinion the best place all over to get a manual of electronics!!!!
;
Well Well Well!!!! Good manual perfect for my hobby!!! As Before you have done a very well done work!!!! Thank you
;
Super nice! Good to have a manual in digital format.
;
Great job supplying the manual.
Many of these products weerepretty obscure, so it was great that you had
the manual for it!
;
Great manual, would not have been able to operate my machine without it!!
James Dawson August 18, 2012
Other useful functions
SHIFT
TEST CH SELECT
Speaker level adjustments
SHIFT
SLEEP QUICK OSD
Sleep timer
This is one of the ways to get appropriate surround effects. Preparation Press [DVD/CD].
Press [SHIFT]i[SLEEP] to select the time (in minutes).
SLEEP 30_----)SLEEP 60_----)SLEEP 90 ^""""" OFF(_ SLEEP 120(__}
SLEEP
1
While stopped and no on-screen display is shown
Press [SHIFT]i[TEST] to output a test signal.
L: Front left C: Center R: Front right RS: Right surround LS: Left surround �There is no output from SW (subwoofer) channel. To cancel the timer Press [SHIFT]i[SLEEP] to select �OFF�. To confirm the remaining time Press [SHIFT]i[SLEEP] again. To change the setting Repeat the procedure from the beginning.
2 3
Press [VOLUME, r] or [s] to set the volume level normally used for listening. Press [3] (increase) or [4] (decrease) to adjust the speaker level for each speaker.
C, RS, LS: `6 dB to i6 dB (L, R: Only the balance is adjustable.) �To adjust the balance of the front speakers While outputting the test signal, press [2, 1]. �Adjust the speaker level to the same level as the front speakers.
SETUP MUTING
Muting
Press [MUTING].
�MUTING� flashes on the unit�s display.
To stop the test signal Press [SHIFT]i[TEST] again.
� To adjust speaker level during play
(Effective when playing multi-channel audio or when Dolby Pro Logic II or Super Surround is on.)
C
1
Press [CH SELECT] to select the speaker.
L #C #R #RS #LS #SW ^-------------------------------------------------} SW: Subwoofer �You can adjust SW only if the disc includes a subwoofer channel. ��SW� does not appear on the display and is not adjustable when Dolby Pro Logic II is turned on. ��S� appears on the display when �MUSIC� or �MOVIE� is selected with Super Surround (� page 22). In this case, you can adjust both surround speaker levels at the same time using [3, 4]. S: `6 dB to i6 dB
To cancel �Press [MUTING] again or reduce the volume to minimum (-- -- dB), then raise it to the required level. �Muting is canceled when you switch the unit to standby.
Using headphones
Main unit only
1
Reduce the volume and connect the headphones (not included).
Headphone plug type: 3.5 mm (1/8z) stereo
2
Press [3] (increase) or [4] (decrease) to adjust the speaker level for each speaker.
POWER
VOLUME
AC IN
C, RS, LS, SW: `6 dB to i6 dB (L, R: Only the balance is adjustable.) �To adjust the balance of the front speakers While �L� or �R� is selected, press [2, 1].
OPEN CLOSE DISC CHANGE DISC DISC CHECK
VOLUME
TUNE MODE
FM MODE
MEMORY
TUNING
DOWN
UP
SELECTOR PROGRESSIVE CD MODE
PHONES
1
2
3
4
5
2
[Note]
Adjust headphone volume with [VOLUME].
�Audio is automatically switched to stereo (2-channel).
Avoid listening for prolonged periods of time to prevent hearing damage.
RQT7969
23
functionsusefulquality/OthersoundandfieldSound
|
|
|
> |
|
