|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Great job supplying the manual.
Many of these products weerepretty obscure, so it was great that you had
the manual for it!
;
Great manual, would not have been able to operate my machine without it!!
James Dawson August 18, 2012
;
excellent value & price! Includes everything you need to know about the NN-C777! I would buy this again.
;
Very satisfied! I was searching for several days, but nope; till I discovered your webside and there it was at a very reasonable price. Keep up the good work!
Paul
Flanders
 ;
Generally speaking good copy; a few pages too hard contrast...
Good service and communication.
4
Connect the speaker cables.
Rear of the speaker
Other speaker setup options
� Attaching to a wall
1 Drive a screw (not included) into a wall. 2 Fit the speaker securely onto the screw(s) with the hole(s). 30�35 mm (13/16q�13/8q) �7.5�9.4 mm (19/64q� 3/8q) 8�11 mm (3/8q� 7/16q)
1 Twist off the vinyl ends of the speaker cables.
_: Copper `: Silver
Push !
Wall or pillar
2 Press the speaker cable into the groove. If there is any excess speaker cable, thread the speaker cable into the opening near the top of the pipe while pulling the speaker cable from the bottom of the base.
�The wall or pillar on which the speakers are to be attached should be capable of supporting 10 kg (22 lb.) per screw. Consult a qualified building contractor when attaching the speakers to a wall. Improper attachment may result in damage to the wall and speakers. �When mounting the front speaker to a wall, we recommend using a string (not included) to prevent it from falling ( � left). �Use of optional speaker cables is recommended for wall mounted front speakers. (You can also remove the speaker cables from the pipes supplied with this system). e.g. Front speaker
Center speaker
230 mm 1 (9 /16z)
150 mm (529/32z)
5
Fasten the speaker cable to the base.
�Using the same polyfoam as in procedure 2 will assist you in safely and securely fastening the speaker cables.
1 Press the speaker cable and thread between the hooks.
2 Fit the speaker cable into the base cover groove as far as possible.
In this position, the speaker will likely fall if moved to the left or right.
Move the speaker so the screw is in this position.
Rear side of base
Cable
� Preventing the speakers from falling over
Preparation Attach screw eyes (not included) to secure the speakers to the wall (�diagram below) �You will need to obtain the appropriate screws to match the walls and pillars to which the screw eyes are going to be fastened. �Consult with a qualified housing contractor concerning the appropriate procedure when attaching to a concrete wall or a surface that may not have strong enough support. Improper attachment may result in damage to the wall or speakers. 1 Thread the string (not included) through the slot on the rear of the speaker to prevent it from falling over. 2 Loop the string through the screw eye and tie tightly. e.g. String (not included) Wall
� Fitting speaker stands (not included)
Ensure the stands meet these conditions before purchasing them. Note the diameter and length of the screws and the distance between screws as shown in the diagram. �The stands must be able to support over 10 kg (22 lb.). �The stands must be stable even if the speakers are in a high position. e.g. Surround speaker
5 mm (13/64z), pitch 0.8 mm (1/32z) 60 mm (223/64z)
Approx. 150 mm (5 15/16z) Screw eye (not included) Rear of the speaker
Attach the stands to these metal screw holes.
Speaker stand (not included) Plate thickness plus 7 to 10 mm (plus 9/32z to 25/64z)
RQT7696
5
Front assembly/Other speaker setup options
|
|
|
> |
|
