|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It is perfect, exactly what we needed. It's like the paper version but less clutter.
 ;
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
MOVING AND STORAGE
WARNING:
Explosive hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. Before using washer, if hot water system has not been used for such a period, turn on all hot water faucets and let water flow for several minutes to release accumulated hydrogen gas. Hydrogen gas is flammable: Do not smoke or use an open flame when flushing water lines.
COLD WEATHER STORAGE
If washer must be stored in seasonal home or storage building, use one of the following storage methods. METHOD 1 1. Turn off water supply faucets and disconnect hoses. Drain water from both hoses. 2. Add one gallon of non-toxic RV antifreeze (available from hardware or recreational vehicle dealers) to washer tub. 3. Push in cycle selector knob and turn to SPIN. 4. Pull knob out and let washer spin for 1�2 minutes to drain water. Some antifreeze will also be lost. (If you have a septic system, contact antifreeze manufacturer and make sure it will not harm system.) 5. Push in cycle selector knob to stop washer. Dry inner wash tub, disconnect electrical plug, and close washer lid. If moving washer, disconnect drain hose. Move and store washer
ONLY in upright position. To remove antifreeze after storage, run washer through a complete cycle using 1/2 cup of detergent. DO NOT ADD CLOTHES TO CYCLE. METHOD 2 1. Push in cycle selector knob and turn to SPIN. Run through complete spin cycle to remove excess water. 2. When spin cycle is complete, push in cycle selector knob to stop washer. 3. Turn off water supply faucets and disconnect hoses. Drain water from both hoses. 4. Dry inner wash tub, disconnect electrical plug, and close washer lid. If moving washer, disconnect drain hose. Move and store washer ONLY in upright position. 5. It is normal for some water to remain inside pump. To prevent damage to washer and pump if remaining water freezes, allow washer to warm 24 to 48 hours after removing from storage, so water can thaw before use.
Cold storage and nonuse periods
COLD WEATHER CARE
If washer is delivered when outside temperature is below freezing or if washer is stored in unheated room or area during cold months, do not operate until washer has warmed to room temperature. Do not install or operate washer where temperatures will drop below freezing.
VACATIONS AND EXTENDED NON-USE
IMPORTANT: To avoid possible property damage from flooding, turn off water supply to washer during extended periods of non-use. To prevent mold or mildew, leave lid open so moisture inside machine can evaporate. When closing your home for extended periods, have service technician drain washer to avoid stagnant water. Unplug cord from electrical outlet. Disconnect hoses from faucets.
MOVING WASHER TO NEW LOCATION
Replace shipping plug under motor and shipping brace in tub. Refer to Installation Instructions for proper procedures whenever washer is moved. See illustration.
Shipping brace
U
Tilt washer back slightly and slide shipping plug into position under washer.
Cardboard base
Shipping plug and location in washer
8
|
|
|
> |
|
