|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very good quality scan of the document. I am very pleased with what I got.
;
PDF Contains
Technical Data, Mechanical data, Detailed Circuit diagram with components value, PCB layout. Actual PCBs Print. Component List, Spare parts code list and Input output detail. It cover LBB1211, LBB1212, LBB1213, LBB1216, LBB1217.
It is the actual Service Manual for SQ10
;
very good manual with clear electrical schemes. Very helpful to find wat was wrong inside my microwave.
 ;
Hi, thankyou for providing the Nordmende Globetrotter original manufacturer's repair manual. Quality is very good and sharp - the PDF file was comfortably small to download. The only question is: why did it take so long to become ready for download?? Many thanks anyway, I fixed the fault in the radio thanks to the circuit.
regards: Nick
;
This was super service.Ordered this manual and was reading the download an hour later
KEX-M8886ZT ,M8886ZT-91
5. Details 1 Frequency characteristics adjustment function � The system changes submodes cyclically every time the [FM1/2] button is pressed when "AUDIO" is displayed. Set EQ Point 1 ¨ Set EQ Point 2 ¨ Set attenuation ¨ "AUDIO" � Set EQ Point 1 The system displays �P1� and EQ management number. The EQ management number ascends/descends every time the UP/DOWN button is pressed.The EQ management number consists of three digits (000 to 286). Initial value is 000 (no setting). � Set EQ Point 2 The system displays �P2� and EQ management number. The EQ management number ascends/descends every time the UP/DOWN button is pressed. The EQ management number consists of three digits (000 to 176). Initial value is 000 (no setting). � Set attenuation The system displays �L� and attenuation value. Use the UP/DOWN button to change attenuation within a range from 0 to -20 dB at increments of 1 dB. Attenuation value is shown in two digits from 00 to 20 (20 = -20 dB). Initial value is 00 (no setting). 2 level adjustment function � The system changes submodes cyclically every time the [TAPE] button is pressed when "AUDIO" is displayed. Set front ¨ Set rear ¨ Set woofer ¨ �AUDIO� � Set front The system displays "F" and level value.Use the UP/DOWN button to change level value within a range from 0 to -80 dB at increments of 1 dB. Level value is shown in two digits from 00 to 80 (80 = -80 dB). Initial value is 00 (no setting). � Set rear The system displays "R" and level value. Use the UP/DOWN button to change level value within a range from 0 to -80 dB at increments of 1 dB. Level value is shown in two digits from 00 to 80 (80 = -80 dB). Initial value is 00 (no setting).
� Set woofer The system displays "W" and level value. Use the UP/DOWN button to change level value within a range from 0 to -80 dB at increments of 1 dB. Level value is shown in two digits from 00 to 80 (80 = -80 dB). Initial value is 00 (no setting). Notes: 1) Pressing the TAPE button during adjustment of frequency characteristics is invalid. Pressing the [FM1/2] button during level adjustment is invalid. 2) The UP/DOWN button mentioned above means the [SEEK] (UP,DOWN) key. Filter 1 : ATT of 30 to 35 dB for receiving frequency Filter 2 : ATT of 5 to 10 dB for receiving frequency The filter should not cause the switch to be set to OPEN when the filter is ON. If setting the switch to OPEN cannot be avoided, duration
43
|
|
|
> |
|
