|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Easy to access. Clear instructions. No problems. Printed fine.
 ;
Great scan but please note that it is entirely in GERMAN.
;
High quality scan of the manual, very quick and easy download and very important, a truly honest price. thanks
;
Minden rendben, de két megjegyzés, az ábrák nehezen kivehetők és a fizetés után 24 órát kell várni a letöltésre.
;
Manual correct, and complete. Downloads cleanly. Format of manual was presumably difficult to PDF to A4, but works reasonably well.
Using Insertion Effects
Amp Sw (Amp Switch) Turns the Amp Type on/off.
Off/On [3 (40 03 05)]
08: Auto Wah
[01H, 21H]
Low Gain -12�+12 [17 (40 03 13)] Adjusts the gain of the low frequency range. Hi Gain (High Gain) -12�+12 [18 (40 03 14)] Adjusts the gain of the high frequency range. #Pan (Output Pan) L63�0�R63 [19 (40 03 15)] Adjusts the stereo location of the output sound. L63 is far left, 0 is center, and R63 is far right. Level (Output Level) Adjusts the output level. 0�127 [20 (40 03 16)]
The Auto Wah cyclically controls a filter to create cyclic change in timbre.
fig.9-8
L Wah R EQ Pan
Effects that modulate the sound (modulation type)
07: Phaser [01H, 20H]
Fil Type (Filter Type) LPF/BPF [1 (40 03 03)] Selects the type of filter. LPF: The wah effect will be applied over a wide frequency range. BPF: The wah effect will be applied over a narrow frequency range. Sens (Sensitivity) 0�127 [2 (40 03 04)] Adjusts the sensitivity with which the filter is controlled. If this value is increased, the filter frequency will change more readily in response to the input level. +Manual 0�127 [3 (40 03 05)] Adjusts the center frequency from which the effect is applied. Peak 0�127 [4 (40 03 06)] Adjusts the amount of the wah effect that will occur in the area of the center frequency. Lower settings will cause the effect to be applied in a broad area around the center frequency. Higher settings will cause the effect to be applied in a more narrow range. In the case of LPF, decreasing the value will cause the wah effect to change less. #Rate 0.05�10.0 [5 (40 03 07)] Adjusts the speed of the modulation. Depth 0�127 [6 (40 03 08)] Adjusts the depth of the modulation. Polarity Down/Up [7 (40 03 09)] Sets the direction in which the frequency will change when the filter is modulated. With a setting of Up, the filter will change toward a higher frequency. With a setting of Down it will change toward a lower frequency. Low Gain -12�+12 [17 (40 03 13)] Adjusts the gain of the low frequency range for EQ. Hi Gain (High Gain) -12�+12 [18 (40 03 14)] Adjusts the gain of the high frequency range for EQ. Pan (Output Pan) L63�0�R63 [19 (40 03 15)] Adjusts the stereo location of the output sound. L63 is far left, 0 is center, and R63 is far right. Level (Output Level) Adjusts the output level. 0�127 [20 (40 03 16)]
A phaser adds a phase-shifted sound to the original sound, producing a twisting modulation that creates spaciousness and depth.
fig.9-7
L
Phaser
EQ
R
Phaser
EQ
+Manual
100�8.0k [1 (40 03 03)]
Adjusts the basic frequency from which the sound will be modulated. #Rate 0.05�10.0 [2 (40 03 04)] Adjusts the frequency (period) of modulation. Depth Adjusts the depth of modulation. 0�127 [3 (40 03 05)]
Reso (Resonance) 0�127 [4 (40 03 06)] Adjusts the amount of emphasis added to the frequency range surrounding the basic frequency determined by the Manual parameter setting. Mix (Mix Level) 0�127 [5 (40 03 07)] Adjusts the proportion by which the phase-shifted sound is combined with the direct sound. Low Gain -12�+12 [17 (40 03 13)] Adjusts the gain of the low frequency range. Hi Gain (High Gain) -12�+12 [18 (40 03 14)] Adjusts the gain of the high frequency range. Level (Output Level) Adjusts the output level. 0�127 [20 (40 03 16)]
94
|
|
|
> |
|
