PANASONIC SCPT1050
Owner's Manual

Adjusting the volume of each speaker: Speaker level adjustments
This is one of the ways to get appropriate surround effects. When �DVD/CD� is selected as the source

Adjusting the speaker output level automatically: Auto Speaker Setup

AUTO

1

While stopped and no on-screen display is shown

Press [TEST] to output a test signal.
� To stop the test signal, press [TEST] again. L: Front left RS: Right surround C: Center LS: Left surround R: Front right

The speaker level settings can be optimized to accommodate your room�s listening conditions so that you can enjoy the ideal surround sound experience. Using the supplied setup microphone, the main unit adjusts the balance of the front speakers, and the volume level of the center and surround speakers automatically. Keep as quiet as possible during the auto speaker setup. Loud voices, air-conditioning noise, or disturbances caused by the wind may lead to incorrect settings. The speakers output loud test signals during the setup. Preparation � Turn off the TV before starting the auto speaker setup. � Make sure that �DVD/CD� is selected as the source (� page 16), and there are no discs in the trays. � Ensure that the wireless link setting is completed (� page 13). � Ensure that headphones are disconnected.

� There is no output from SW (subwoofer) channel.

2 3

Press [VOLUME, r] or [s] to set the volume level normally used for listening. Press [3] (increase) or [4] (decrease) to adjust the speaker level for each speaker.
C, RS, LS: `6 dB to i6 dB

� Adjust the speaker levels to the same level as the front speakers.

� To adjust speaker level during play
(Effective when playing 5.1-channel sound or when Dolby Pro Logic II/Super Surround is on, and Surround Music is off.) 1 Press [CH SELECT] to select the speaker. L #C #R #RS #LS #SW ^----------------------------------------------------} � You can adjust SW (Subwoofer) only if the disc includes a subwoofer channel and ��PLII� is not lit. � �S� appears on the display when Super Surround is on (� page 32). In this case, you can adjust both surround speaker levels at the same time using [3, 4]. S: `6 dB to i6 dB 2 Press [3] (increase) or [4] (decrease) to adjust the speaker level for each speaker. C, RS, LS, SW: `6 dB to i6 dB (L, R: Only the balance is adjustable.) � To adjust the balance of the front speakers, while �L� or �R� is selected, press [2, 1].

1

While stopped

Connect the setup microphone.
� Place the microphone at the actual seating position and the same height of hearing level (e.g. on your sofa�s headrest).

SETUP MIC

2

Press and hold [�AUTO].
� The test signal is output from each speaker. � �COMPLETE� will be displayed in the main unit�s display when the setting is completed. Unplug the setup microphone. � To cancel the setup, press and hold [�AUTO] again (�CANCEL� will be displayed in the main unit�s display).

[PT1050] Enhancing the bass sound: H.BASS

H.BASS

You can enhance low-frequency sound so that heavy bass sound can be heard clearly, even if the acoustics of your room are not optimal. The unit automatically selects the most suitable setting according to the type of playing source.

[Note]
RQTX0064 Using sound effects

The settings will return to default if Auto Speaker Setup is cancelled.

Press [H.BASS].
Each time you press the button: H.BASS ON,------.H.BASS OFF The setting you make is retained, and recalled every time you play from the same type of source.

[PT1050] Enhancing the surround sound effect: Surround Enhancer

SRD ENH

Automatically adjusts each speaker to enhance the surround sound effect. When playing two-channel audio, the audio of the L/R front speakers is also output through the rest of the speakers creating a surround sound effect.

Press [SRD ENH].
Each time you press the button: SRD ENHANCER ON,------.SRD ENHANCER OFF

DDTS

PL

SRDE. PRG PGM RND RDS EQ W1 W2 WS

33