|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I am very happy with the owner's manual. I bought a used Casio and was so relieved that I was able to get a hold of a owner's manual. It was very easy to download the manual and I had no problems with printing it. Thank you! Nancy Whalen
;
The purchased manual is an high-quality scan of the original JVC paper-based Owner´s Manual. I am very satisfied!
;
Very satisfied with received document, all is right, Thank You very much, it was a Pleasure to work with You.
 ;
great site, the most easy and fastest way to find the manual you need, no 5 star because the manual was only available in german, but I speak german as well so no problem for me.
;
thanks for this download i got a pioneer bdp-lx70a blu-ray player and it had no manual i search everywhere on the internet and came across owner-manuals.com and i found that it was so easy to find and downloaded from this site if i ever need a manual again this would be the first place that i would come too thanks guys
adaptor onto the back of the speaker in two places, as shown. The floor stand adaptor screws may be found in Hardware Bag B. Use the larger screw in the upper screw hole, and the smaller screw in the lower screw hole.
Screw the floor stand adaptor into the floor stand�s threaded insert until the speaker is firmly attached to the stand. Back off slightly from the fully tightened position until the speaker is oriented as desired, then rotate the thumbwheel at the bottom of the floor stand adaptor to
secure the speaker to the stand.
WALL-MOUNTING
4 3 2
6 7
1
1
2 3 4
8 5
5 8
Important Safety Note: The customer is solely responsible for proper selection of mounting hardware not included with the speakers, and for proper assembly and installation of the wallbrackets, including but not limited to the selection of appropriate weight-bearing supports and proper use of the bracket. JBL disclaims any liability for the selection of mounting hardware and/or bracket installation. Be sure to follow these bracket assembly and installation instructions carefully. If you have any questions or doubts about your ability to correctly wall-mount the speakers, consult with your authorized JBL dealer or custom installer. Step 1: Unscrew and remove the large Molded Nut �. If necessary, use the supplied
6
Metal Bar � as a lever by inserting it into one of the holes in the outer edge of the Molded Nut �. Step 2: Firmly grasp the Ball and Shaft £ and pull it straight out of the Attachment Plate ¢. Avoid leaning it to the side for leverage, as this may break off a tab. Step 3: Slide the Molded Nut � onto the Ball and Shaft £ with the threaded opening facing the ball. Thread the Metal Nut ¡ all the way onto the Ball and Shaft £, with the star washer side away from the ball. Refer to the exploded drawing for the proper orientation of parts. Step 4: Screw the Ball and Shaft £ into the Threaded Insert § on the back of the Satellite Speaker ¶ until it is fully seated in the Threaded Insert §, but do not tighten, as you might dislodge the Threaded Insert
§. Such damage would not be covered under the warranty. Step 5: Tighten the Metal Nut ¡ with the star washer side between the Metal Nut ¡ and the back of the Satellite Speaker ¶, using large needle-nose pliers, until it is firmly seated against the back of the Speaker ¶ and has locked the Ball and Shaft £ and the Satellite Speaker ¶ together. Note that once the Metal Nut ¡ is fully tightened, it may embed some marks on the back of the Satellite Speaker ¶. However, these marks will be covered by the Metal Nut ¡. Step 6: Mount the Attachment Plate ¢ into a wood stud on the wall, using four #10 pan-head wood screws at least one inch long (not supplied) �. Make sure that all four screws are driven into the stud and not into drywall.
|
|
|
> |
|
