|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I AM HIGHLY IMPRESSED BY THE EASE OF USE OF THIS DOWNLOAD SERVICE. INSTRUCTIONS ARE CLEAR AND SIMPLE TO FOLLOW....EVEN BY TECHNOPHOBES SUCH AS MYSELF. THE EMAILS POINT YOU IN THE RIGHT DIRECTION...ITS SO EASY PEASY. THE DOWNLOAD CHOICE OF USER MANUALS IS EXTENSIVE AND I COULD NOT FIND A CHEAPER OR MORE EFFICIENT SERVICE ON THE INTERNET. I COULD NOT HAVE MADE A BETTER CHOICE OF INFORMATION PROVIDER. SHOULD I EVER NEED ANOTHER USER MANUAL, THEN THIS IS THE FIRST CHOICE SITE. COULD NOT BE BETTER PLEASED!!!!!!!...MANY THANXES FROM JIM BURNS
;
I was impressed with the quality of service (frequent e-mails to let you know the status of your order), and the speed at which the download became available. The manual was a life saver and was not easy to track down. Thank you for such an excellent service.
;
the manual was just what i wanted it had all the revelent information required to operate the hifi .Iwould use any manual i downloaded for any item which needs a manual
;
Die gewünschte Bedienungsanleitung wurde vereinbarungsgemäß in deutsch bereitgestellt. Sie ist gut lesbar. Kein Kauderwelsch.
Danke für den Service.
;
GOOD SERVICE MANUAL GOT ALL THE INFO. THAT I NEEDED..
Using the internal sound generator
Part Output Assign MFX, 1, 2, 1L, 1R, 2L, 2R, PATCH This specifies where the output signal of the part will be sent. MFX: 1: 2: 1L: 1R: 2L: 2R: PATCH: * Output to MFX. Output the unprocessed sound from OUTPUT 1, without using MFX. Output the unprocessed sound from OUTPUT 2, without using MFX. Output the unprocessed sound from the L jack of OUTPUT 1. Output the unprocessed sound from the R jack of OUTPUT 1. Output the unprocessed sound from the L jack of OUTPUT 2. Output the unprocessed sound from the R jack of OUTPUT 2. The settings of the patch (instrument) will be applied. If the patch is set to use MFX, the sound will be sent to MFX. If not, the DRY sound will be output.
Select 1L, 1R, 2L, or 2R when you want to use the output jacks as four parallel outputs.
PART Output MFX Select MFX-A, MFX-B, MFX-C If MFX is selected for Part Output Assign, select one of the three MFX units to which the sound will be sent. PART Dry Send Level 0�127 This specifies the level of the output to the output destination you�ve selected for Part Output Assign.
â� Parameters common to all parts (GM2 mode, Native mode)
The following parameters common to all parts can be edited from the panel of the SD-80. Master Volume 0�127 Adjusts the volume of all parts. Increasing this value will increase the volume. The basic overall volume of the SD-80 is adjusted with the [VOLUME] knob. If the [VOLUME] knob is set to the minimum position, there will be no sound even if you use this parameter to raise the volume. Master Fine Tuning 415.3�440.0�466.2 Hz
When you are playing in an ensemble with other instruments, or want to adjust the SD-80 to the tuning of another instrument, you can adjust the Master Tuning in a range from 415.3 Hz to 466.2 Hz. The displayed value (for example 440.0 Hz) is the frequency of the A4 note (note number 69). Master Coarse Tuning -24�0�+24
This parameter transposes the pitch of all parts in semitone steps. For example, when using your sequencer software to play song data, this parameter can be adjusted to change the key without having to change the settings of your software. As another example, you can adjust this parameter to transpose the pitch to a comfortable range when you want to sing along with song data that is too high or too low for your voice. Increasing (decreasing) this value by one will raise (lower) the pitch by one semitone. Thus, a setting of 12 will change the pitch by one octave. With a setting of 0, the pitch will not be transposed. This parameter lets you adjust the pitch in semitone steps over a range of +/-2 octaves. The pitch of drum parts will not change even if you adjust the Master Coarse Tuning to transpose all parts.
*
38
|
|
|
> |
|
