|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
 ;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
Installing the display vertically
This display can be installed either horizontally or vertically using the supplied display stand.
While sliding the stopper up, close the display stand.
To close the display stand
Selecting the on-screen menu language (LANGUAGE)
English, German, French, Spanish, Italian, and Japanese versions of the on-screen menus are available. The default setting is English.
Selecting the input signal
You can connect two computers to this monitor using the INPUT 1 and INPUT 2 connectors. To select one of the two computers, use the INPUT button. Press the INPUT button. The input signal and corresponding input indicator, �1� (INPUT 1) or �2� (INPUT 2) change each time you press this button.
To switch to the horizontal or vertical viewing position
First install the supplied WinPortrait (for Windws 95/98 and NT4.0) or MacPortrait (for Macintosh). To switch the view, press Shift + Ctrl + R on the keyboard. For more information, see the supplied software�s instruction manual.
1 Press the MENU button.
The stopper MENU
PHA S E
INPUT
16
To install the display horizontally or vertically
Open the display stand until the click sound is heard. Put the display on the stand, aligning the mark which shows the stand position on the display.
,
1 2 OK
Using the headphones
Horizontal installation You can listen to the audio signals from your computer or other audio equipment using headphones. Connect the AUDIO IN jack to the audio output jack of your computer or other audio equipment using the supplied audio cord.
EX I T
2 Press the M(+)/m(�) buttons to select m.
B A S S BOOS T ON OF F
,
Adjusting the volume 1 Press the 2 +/� buttons.
The VOLUME menu appears on the screen.
VOL UME
Notes � You cannot select the input signal when displaying the main menu on the screen. � If no signal is input to the selected connector, NO INPUT SIGNAL or CABLE DISCONNECTED appears on the screen. After a few seconds, the monitor enters the power saving mode. If this happens, select the other connector using the INPUT button.
EX I T
GB
3 Press the M(+)/m(�) buttons to select
(LANGUAGE) and press the OK button.
40
L A NGU AGE
The stand positioning mark
,
Vertical installation
INPUT
,
2 Press the 2 +/� button to adjust the volume.
1 2 OK
,
ENG L I SH DEU T SCH FRAN�A I S ESPA�OL I TAL I ANO
1-4
The menu automatically disappears after about 3 seconds.
Notes � You cannot adjust the volume when displaying the main menu on the screen. � When your monitor is in power saving mode, no sound comes from the headphones.
EX I T
4 Press the M(+)/m(�) button to select a language.
� ENGLISH � � � � � DEUTSCH: German FRAN�AIS: French ESPA�OL: Spanish ITALIANO: Italian : Japanese
The stand positioning mark
To close the menu Press the MENU button once to return to normal viewing. If no buttons are pressed, the menu closes automatically after about 30 seconds.
10
11
|
|
|
> |
|
