|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
again you did a very good job. It was fast too. Photocopy are really readable and clear
 ;
Probably it never existed a 1081 official service manual from Commodore, it's look more like a NAPCEC service manual & diagrams compilation of the 1084 series and his variants, like the nap6523, 8cm505, 1084S, 1084P and obviously the 1081. It's more complete than other scans and the quality of the scans also are far superior. It has two circuit diagrams variants of the 1081, mono and stereo versions. It doesn't include a diagram for the Philips CM8500 or CM8501, they look like the 1081 but they are slightly different.
;
Rapid, clear well done as all the scheme I downloaded from this site. Great job very functional and very useful
;
Great copy of the manual, has all information required for servicing,
;
I work at an authorized service center and I can tell if a manual is as it should be. This one is. It may be a scan, but a very good one at that. The interesting part for me was the curcuit diagram which was scanned at high quality, making it as good as the original. I will definitely be back as a customer. I need not say this, but I will: the price was the best. Thank you owner-manuals.com .
ADJUSTMENT
1. Procedures of how to go to service mode. 1) Enter the service mode of this unit by turning on the power while pressing and holding the �r� key simultaneously. 2) Press �MENU� key��MAINTAIN. 3) Press �OK� key to enter the service menu. 4) Select the desired function. 5) Press the �MENU� key to exit OSD. 6) Turn off the power and then turn on it again. The monitor then enters the normal mode. To enter the service again, repeat the procedure described above. Note W/B readjustment is required after the panel, board and microcomputer are replaced. However, be sure to perform aging for more than 30 minutes for RGB reset before W/B adjustment. 2. Setup 1) Prepare timing and pattern data for a signal generator according to the Sony timing specifications. 2) Connect a monitor video cable to the signal generator. 3) Put Color Analyzer(ex. CA-110) 50cm away from the monitor, specify it vertically in the center of the display, and adjust the focus to the optimum level using an eyepiece. 4) Put the monitor and Color Analyzer(ex. CA-110) in a light-shielded room. 5) Set up [SERVICE MODE] of the monitor. 3. Operation Data is manually set to improve the productivity. The brightness, contrast, and backlight are set to 50, 70 and 100 respectively. After that, the default data of the color temperature to be adjusted is set. 4. Warm up time Warm up for 30 minutes before performing any adjustment. 5. Adjustment for White Balance a. Display SMPTE at SXGA/60Hz(Input level 0.73V). b. Set up [SERVICE MODE]. c. Click �INITIAL EEPROM� and again setup Service Mode. d. Click �WHITE BALANCE� and then select �AUTO�. 6. 9300K color adjustment a. Select �9300K� in �COLOR TEMP� and enter. b. Use a 35%(89Gray) IRE white video field in the primary mode. c. Adjust �SUB CONTRAST � to secure the color temperature. d. Press �MENU� key to exit adjust mode. 7. 6500K color adjustment a. Select �6500K� in �COLOR TEMP� and enter. b. Repeat the adjustment procedure as steps b to d at 9300K.
� 11 �
SDM-S73/S93 (E)
 $4.99 SDMS73 SONY
Owner's Manual Complete owner's manual in digital format. The manual will be available for download as PDF file aft…  $4.99 SDM-S73 SONY
Quick Start Quick start guide ( sometimes called quick guide ) contains most important information on how to use…
|
|
|
> |
|
