|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It took about 24-hours after my payment before I was able to get to the download. Apparently, payment processing is not 100% automated. That is no big deal, just be aware of that going in.
After I got to it, it was in good shape, easy to read, etc. Not some cheap FAX copy looking thing.
Also, this site was the cheapest I found. Another Plus!
 ;
Good price, very legible manual, exactly what I needed -- but had to wait a day to actually get the download of the manual. Would have preferred to download it immediately after payment rather than waiting for someone to "process" my order. I was surprised that I had to wait that long.
 ;
As the only source for this manual it rather rank quite high since it is well scanned and perfectly readable.
 ;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
 ;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
5
6
7
8
7. GENERAL INFORMATION
7.1 DISASSEMBLY
Removing the Amplifier Module
1 ) Reverse the cabinet and remove the Rubber Pad (4pcs.). Unfasten 4 screws attaching the Reflective Board. 2 ) Unfasten 4 screws attaching the Speaker. Disconnect the Speaker Cord from the Speaker. 3 ) Remove the Amp Box Press Board. 4 ) Loosen the cables styling in the cabinet 5 ) Unfasten 6 screws attaching Front Panel. Next disconnect Jumper Read(9P) from FRONT ASSY. 6 ) Unfasten 16 screws attaching the Amp Box L and S. 7 ) Pull out the Amp Box from the cabinet and insert a hand to the frame which attached the Amp Box Press Board, and disconnect the Connector from the Amplifier Module. The Connector which needs to be disconnect: All the Connectors from the Transformer The Connector(2P) from the Front Panel Assy
Removing the Speaker
1 ) The Speaker is attached to the bottom board by 4 external screws. To detach it, first remove the Rubber Pad(4 pcs.) and Reflective Board. Next unfasten those screws. 2 ) When attaching the Speaker, it attaches according to direction of a photograph (lower left figure).
A
Removing the Front Panel Assy (FRONT, LED, SW ASSYS)
1 ) Before removing the Front Panel Assy, first remove the Speaker and loosen the Jumper Read(9P) styling. 2 ) The FRONT, LED and SW ASSYS are attached to the Front Panel. The Front Panel is attached to the cabinet by 6 external screws. To detach it, unfasten those screws. 3 ) Disconnect the Jumper Read(9P). 4 ) Disconnect the Connecting Cord(2P) from Rear Panel of Amplifier Modure. It is able to detach the Front Panel Assy. 5 ) The FRONT ASSY is attached to the Inner Panel. When removing the Inner Panel, first remove the Volume Knob. And then unfasten 5 screws of the Front Panel rear side. The Nut for Volume is locked by adhesives. When attaching the FRONT ASSY again, lock of the Nut is needed. (refer to 37-38 pages) 6 ) The SW ASSY is attached to the Inner Panel. After detaching the Inner Panel, Back Cover and Power Button, it is able to detach the SW ASSY. 7 ) After detaching the Inner Panel, it is able to detach the LED ASSY. 8 ) When attaching the Volume Knob again, push the C RING until it reaches the rib of the Volume Knob. C RING
B
Note 1: The Connector has a stopper. When disconnecting, it unplugs with grasping a stopper.
C
Stopper
8 ) Pull out the Amplifier Module. Go to " Removing the Amplifier Module Assys" next page.
D
Removing the Power Transformer
1 ) The Transformer is attached to the Transformer Attachment Board by 4 screws. The head of Screws are locked by adhesives. 2 ) The Transformer Attachment Board is attached to Back Board by 4 external screws. The Screws are locked by adhesives. When detaching the Transformer, first remove the Speaker and the Amplifire module. And then, unfasten those screws. 3 ) When attaching the Transformer to the Transformer Attachment Board and the Transformer Attachment Board to Back Board again, lock of the Screws are needed. (refer to 37-38 pages)
E
Note : This photograph may show a different model. However, the method for disassembly is the same.
F
S-EW5
5 6 7 8
35
|
|
 |
> |
|