|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank You for fast delivery for the sheme.
Everything allright.
Thanks & best regards Franz
 ;
again you did a very good job. It was fast too. Photocopy are really readable and clear
;
Probably it never existed a 1081 official service manual from Commodore, it's look more like a NAPCEC service manual & diagrams compilation of the 1084 series and his variants, like the nap6523, 8cm505, 1084S, 1084P and obviously the 1081. It's more complete than other scans and the quality of the scans also are far superior. It has two circuit diagrams variants of the 1081, mono and stereo versions. It doesn't include a diagram for the Philips CM8500 or CM8501, they look like the 1081 but they are slightly different.
;
Rapid, clear well done as all the scheme I downloaded from this site. Great job very functional and very useful
;
Great copy of the manual, has all information required for servicing,
5
6
7
8
8. PANEL FACILITIES
1 Power indicator (STANDBY/ON)
A
FRONT PANEL 1
ST ANDBY/ON POWER
VOLUME
MIN
MAX
2 3
Lights green when the power has been switched ON. Lights green when the speakers receive an audio signal. If the power is switched OFF only briefly, the indicator lights green when power is restored. If no signal is present for more than 8 minutes, the subwoofer automatically reverts to standby mode and the power indicator lights red. If, subsequently, a signal is received, power automatically comes back on and the power indicator lights green.
POWERED SUB WOOFER
2 POWER switch
Pressing once switches the unit ON. Press again to switch OFF. NOTE: If you are planning on switching the unit OFF for a long period of time, make sure to check that the indicator light has gone out after switching OFF.
B
3 Volume knob (LEVEL)
� � Sets the subwoofer volume. Turn the knob slowly from the MIN position. With this unit, the bass level can be independently set, so do not turn up the bass on the stereo amplifier.
REAR PANEL 4
LINE LEVEL INPUT
LINE VOLTAGE SELECTOR SWITCH
4 Line Level Input terminal (LINE LEVEL INPUT)
240V
220- 110230V 127V
Connects to the stereo amplifier�s SUBWOOFER PREOUT terminal, with the specially provided RCA plug cord. When depressed (180°), the output phase becomes the reverse of the input signal, and when raised (0 °), it is in the same phase as the input signal.
C
AC IN
7
5 Phase switch (PHASE 0 °/180 °)
5 6
PHASE 180° 0° AUTO ST ANDBY ON OFF
� Normally, the switch is set to ( 0 ° ). But when the sound connection between the subwoofer and the left and right speakers sounds unnatural, tyr switching to 180 ° and set the switch in the position where the sound is natural.
6 Auto Standby switch (AUTO STANDBY)
Switches the Auto Standby feature on/off. Auto Standby When switched ON (the default setting is OFF ), the Auto Standby feature becomes active. In this mode, if there is no input signal for eight minutes the system automatically switches to standby. The power is automatically switched on again if an input signal is detected.
D
7 AC INLET
240V 220230V 110127V
� Connect the power cord to the powered subwoofer unit�s AC INLET.
AC IN
E
� Connect the power cord to a AC socket.
NOTE � There may be cases where a connected component outputs noise or some other non-audio signal which causes this system to automatically power on when in Auto Standby mode. If this happens, switch off the Auto Standby mode and switch the system on/off manually.
F
S-EW5
5 6 7 8
41
|
|
|
> |
|
