|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This scanned manual is well done in that most all the pages except for one is straight and clear- the way I would do them. One page was upside down but that happens. For the money that is charged on this site you get a pretty good deal. Now with complex repairs, I still prefer to us paper manuals which I have to buy at stereomanuals but the one I got here was much less than the $45 he was charging but this is a larger than normal manual for three different units. I am a picky manual user because I have used original manuals from Sony and Teac.
;
Very useful service manual, was exactly what i needed.Good quality,reasonable price.Thank you.
;
Acurate informations inside the SM and I could repair my old Sansui SC-3330 without any problems. Thanks.
;
I used it to repair a NAD 7030, but unfortunately, the 7045 is different !
But documentation was useful.
;
Content A4 and A3 format pages. Exactly what I needed to restore my old receiver.
ORDER NO.
Front Center Rear
RRV2359
S-HS77-F
S-HS77-CR
FOR PRECAUTION OF REASSEMBLY AND DISASSEMBLY
[ Front speaker ] The grille is attached to the cabinet by catches. Detach by pulling it toward you. The woofer is attached to the baffle by 4 external screws. To detach it, unfasten those screws. When attaching it, face its terminal downward. The midrange is attached to the flange lower side by 4 external screws. To detach it, unfasten those screws. When attaching it, face its terminal downward. The tweeter is attached to the flange upper side by 2 external screws. To detach it, unfasten those screws. When attaching it, first reattach the packing around tweeter diaphragm, then face its terminal downward. The flange is attached to the baffle by 4 external screws. To detach it, unfasten those screws. When attaching it, face it downward. To detach the midrange or tweeter, first remove the flange. Then remove it. The input terminal is attached to the back board by press-fitting and applied with adhesive. To detach it, pry it open by inserting a flat blade screwdriver into lower side. The Network Assy is attached to the input terminal by soldaring.
SPEAKER SYSTEM
XMA/NC
XMA/NC
[ Center speaker ] The grille is attached to the cabinet by catches. Detach by pulling it toward you. The woofer is attached to the baffle by 4 external screws. To detach it, unfasten those screws. When attaching it, first exchange the flange, then face its terminal downward. The tweeter is attached to the baffle by 4 external screws. The cosmetic packing is attached to the flange applied with adhesive.To detach the tweeter. First remove the cosmetic packing, then unfasten those screws. When attach it, do so that it will move vertical. The tweeter wires, connected in the middle of network Assy , are covered with the insulating tape. The input terminal is attached to the back board by press-fitting. To detach it, pry it open by inserting a flat blade screwdriver into lower side. The Network Assy is attached to the input terminal by soldaring.
[ Rear speaker ] When exchange the rear speaker, do it with the CS Assy (R).
PIONEER CORPORATION
4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2000
T-ZZM JULY 2000 Printed in Japan
|
|
|
> |
|
