|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
High quality scan of the manual, very quick and easy download and very important, a truly honest price. thanks
 ;
Minden rendben, de két megjegyzés, az ábrák nehezen kivehetők és a fizetés után 24 órát kell várni a letöltésre.
;
Manual correct, and complete. Downloads cleanly. Format of manual was presumably difficult to PDF to A4, but works reasonably well.
;
This was a hard to find manual. When I did find it , some sites wanted way too much for the file.
Owner-manual .com had it for a really reasonable price. Not only that but it was sent very quickly and was a quality scanned document, unlike some others I purchased from a different site.
Good job guys!!
Larry
;
Fast and courteous service. Product delivered as described. Thank you.
Model name
SKF-4600 Front speaker system � 2 SKS-4600 Center speaker system Surround speaker system SKC-4600 � 1 SKM-4600 � 2
SKF-4600
1. Strip the insulation of speaker cables, and twist the core wires tightly. 2. Loosen the 3. Fasten the terminal screw, and terminal insert the wire into screw. the hole (until the core wires are inserted fully).
Connection
� Turn the sound volume to the minimum and disconnect the power cord from the amplifier before connecting the speaker cables. � The nominal impedance of this speaker system is 6 �. Use only amplifiers capable of handling this impedance. � Use the supplied speaker cables to connect between speaker�s input terminals and the amplifier�s speaker terminals as illustrated below. � Connect the speaker cables securely to the terminals, with the core wires twisted properly. In this case, make sure that the core wires do not touch each other. Note that a short circuit in core wires may result in damage to the amplifier. Connecting to AV amplifier
SKF-4600 Front right speaker SKF-4600 Front left speaker
15 mm
SKC-4600 / SKM-4600
1. Strip the insulation of speaker cables, and twist the core wires tightly. 2. While pressing the lever, insert the wire into the hole, and then release the lever.
3. Make sure that the terminals are gripping the core wires, not the insulation. SKC-4600 Center speaker
�+
�+
Green
�+
Before turning on the amplifier�s power switch: � Make sure that the positive (+) and negative (-) speaker cables do not contact each other. Otherwise, a short-circuit may occur, causing damage to the amplifier.
FRONT SPEAKERS SURROUND SPEAKERS CENTER SPEAKER
Red White Blue
A
L L
B
L
R R R
� Be sure to connect the speaker cables with correct polarity (connect the speaker�s positive (+) and negative (-) binding posts with the amplifier�s corresponding speaker terminals). Reversed polarity results in impaired bassrange reproduction, causing mislocalization of the sound image. Also, be sure to connect the Right and Left speakers with the amplifier�s corresponding speaker terminals. � Pull lightly on the speaker cables to ensure that they are connected firmly.
SURROUND BACK SPEAKER
Gray
�+
SKM-4600 Surround right speaker
�+
SKM-4600 Surround left speaker
27122965
ANTENNA COMPONENT VIDEO
INPUT 2 INPUT 1 OUTPUT
CAUTION: SPEAKER IMPEDANCE
6 OHMS MIN. /SPEAKER
FRONT SPEAKERS Y
SURROUND SPEAKERS
CENTER SPEAKER AC OUTLETS
A
L L
B
L
FM 75
AM
PB
REMOTE CONTROL
PR DIGITAL INPUT
2 OPTICAL 1
R R R
DIGITAL DIGITAL OUTPUT INPUT
OPTICAL COAXIAL
VIDEO 3 VIDEO 2
IN IN
OUT
VIDEO 1
IN
DVD
IN
MONITOR OUT VIDEO
SURROUND BACK SPEAKER
S VIDEO
AC 230-240 V 50 Hz SWITCHED TOTAL 100W MAX.
CD
IN
TAPE
OUT IN IN IN OUT IN FRONT SURR CENTER
L
SUBWOOFER PRE OUT
L R
L R R
VIDEO 3 VIDEO 2 VIDEO 1 DVD
SUB WOOFER
AV Amplifier
En-2
|
|
|
> |
|
