|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
A good manual! fast service and good qualityi for pdf document.
thanks!
 ;
Very helpful and complete manual. Maybe only one negative is schematics have sometimes unreadable name of the parts. But it's not a big problem.
;
Excellent high quality schematics brought my old Heidelberg back to life. Fast download at a reasonable price. Thanks.
;
This document is just what I was looking for, it´s very useful, it contains adjustment procedures for the final stage of the power amp and also
has a complete wiring diagram and description of the main semiconductors used in the design.
;
Dear Sirs,
Thank you for the fast support, the manual does provide all necessary information to repair the radio. All schematics are in a good quality for reading.
The manual fits 100% to my requirements as a technican.
Kind regards Thomas
Alignment and Adjustments
4-6 Other Adjustments
4-6-1 Screen Adjustment
1. Warm up the TV for at least 30 minutes. 2. Turn to the Video Mode (No Signal) using a remote-control. 3. Connect an oscilloscope to RK,GK,BK. 4. Adjust the VR (VR501, VR531, VR561) screen so that RK, GK, BK pulse is 20Vp-p each. (Turn the R,G,B VR screen fully counterclockwise in the area of each flyback line.) 3. Select SBT by pressing the Volume +/- keys. 4. Adjust so that the 63 step on the right side of the screen is not seen (Use the Volume +/keys). 5. Press the Menu key to exit.
4-6-4 High Voltage (29KV) Check
PRECAUTION
1. Input a lion head pattern. 2. Select �STANDARD� video mode.
4-6-2 White Balance Adjustment
3. Warm up the TV for at least 10 minutes. 1. Select the �STANDARD� video mode. 4. Use a 1000:1 probe. 2. Input 100% white pattern. 3. In the stand-by mode, press the remote-control keys in the following sequence: Displsy � Menu � Mute � Power ON 4. Warm up the TV for at least 30 minutes. 5. Input a 10-step signal. 6. R-cut off, B-cut off, and G-cut off by pressing the Volume +/- keys. 7. Adjust the low light with viewing the dark side of the screen. 8. Select R-drive, G-drive, and B-drive by pressing the Volume +/- keys. 9. Adjust the high light with viewing the light side of the screen. 10. If necessary, redo adjustments 6~9. 11. Press the Menu key to exit. 3. Adjust VR (RR402S) so that the voltage becomes 2.25V. After the adjustments are complete, be sure to mount VR (RR402S) correctly.
ADJUSTMENT
1. Connect the (+) terminal of the 1000:1 probe to the high voltage distributor and the (-) terminal to GND (located on the deflection board). 2. Adjust RR471S (located on the deflection board) so that the digital meter indicates DC 29V ± 0.1V.
4-6-5 F.S. (Fail Safe) Adjustment
Note : The finished product has a well-mounted VR (RR402S). If necessary, do the F.S. adjustments in the following sequence. 1. 2. Use a digital multimeter. Connect the digital multimeter to the JIG pin (DZ482S) terminals
4-6-3 Sub-Brightness Adjustment
4. 1. Input a sub-brightness adjustment signal. (TOSHIBA PATTERN) 2. In the stand-by mode, press the remote-control keys in the following sequence : Displsy � Menu � Mute � Power ON
4-22
Samsung Electronics
|
|
|
> |
|
