|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Quick site processing. A complete and very useful manual with all details. Thank you!
;
Quick service response. A useful and very rare service manual with all details. I recomend this service.
;
I ordered this manual sometime in the afternoon and I received it on my e-mail the same evening.
This is a fantastically good and properly scanned copy of the original manual. All pages are of the same scale and they overlap each other. It means that you can print the manual and easily make it as a convenient paper manual.
The content of the manual is fantastic. Alignment descriptions, PCB layouts and elementary diagrams are explicit and precise. I immediately found what I was looking for. Thanks to this manual and Owner-Manuals.com my amplifier is alive again. Many thanx indded!
;
The manual was well-scanned and easy to read. As an added bonus, the Operator's Manual was bundled with the Service Manual!
I'd definitely use owner-manuals.com again.
;
Finally, i found one website, where i can download this service manual , and fix my hifi. The service manual is very good, and easy to download and to print.
6. ADJUSTMENT PROCEDURE
(1) ALIGNMENT INSTRUCTIONS
EQUIPMENT NEEDEDIMPORTANT AM Signal Generator1.Check power-source voltage. FM Signal Generator2.Set the function switch to band aligned. Oscilloscope3.Keep the function input as low as possible to adjust. VTVM(AC,DC) accurately. Test loop antenna (MW Adjustnent) 4.Modulation and modulation frequency. Dummy antenna(FM Adjustment) Stereo signal modulator. Distortion analyzerModulationModulation Frequency.
MW 2 3 1503KHz Max sensitivity CT01 2 3 100.10MHz Repeat steps 1 and 2 several times. NO STEP 1
FREQUENCY
(3) MW TRACKING ADJUSTMENT
Signal Generator : Connects to the MW Ant. Coil through the loop antenna. Adjust for the indication of VTVM of the wave form of scope to be maximum.
(5) FM MONO DISTORTION ADJUSTMENT
DC VOLTMETER Connect to TP02 (-),TP03 (+) through the chockcoil (100 H). Signal Generator Connect to FM ANT. Jack (FM IN) through thedummy. Distortion Meter Connect to the output.
ADJUSMENT L102
(7) FM/MW TUNED LEVEL ADJUSTMENT
FM Signal Generator : Connect to FM ANT. Jack (FM IN) through the dummy. MW Signal Generator : Connect to MW ANT. Coil thriugh Loop antenna.
ADJUST FOR Max sensitivity
NO 1
FREQUENCY 100.10MHz
ADJUST FOR DC Voltmeter 0V min T.H.D
ADJUSTMENT T101
BAND STEP SIGNAL GENERATOR ADJUST FOR FM 1 2 MW 1 2 100.10MHz 30dB 100.10MHz 30dB 999KHz 80dB 999KHz 80dB TUNED TUNED TUNED TUNED ON OFF ON OFF
ADJUSTMENT VR02 VR02 VR01 VR01
612KHz
T102
Repeat steps 1 and 2 several times
EQUIPMENT NEEDEDIMPORTANT
AM Signal Generator1.Check power-source voltage. FM Signal Generator2.Set the function switch to band aligned. Oscilloscope3.Keep the function input as low as possible to adjust. VTVM(AC,DC) accurately. Test loop antenna (MW Adjustnent) 4.Modulation and modulation frequency.
AM-SG
MHz
AC EVM
OSCILLOSCOPE
FM-SG
MHz OUT
DC EVM
75ohm
UNIT
AM LOOP antenna
60cm OUTPUT terminal
TP12 Chassis TP13
Choke coil 100 H output
MODULATION
MODULATION FREQUENCY
DISTORTION ANALYSER
MW FM
30% 100%(75KHz)
400Hz 400Hz
(2) TUNING FREQUENCY RANGE ADJUSTMENT
(FM) DC VOLTMETER CONNECT TO TEST POINT TP1 and GND (MW) DC VOLTMETER CONNECT TO TEST POINT TP1 and GND
NO 1 2 BAND FREQUENCY FM MW 87.50MHz 522KHz ADJUST FOR 1.5V 1V ADJUSTMENT L4 L103
(4) FM-RF ADJUSTMENT
Signal Generator : Connects to FM ANT. JACK (FM IN) through the dummy.
(6) FM STEREO SEPARATION
PILOT SIGNAL ON ADJUST FOR Different of R and L Must be maximum ADJUSTMENT VR03
NO 1 2
FREQUENCY 90.10MHz
ADJUST FOR Max sensitivity
ADJUSTMENT L1,L2,L3
STEREO OSCILLOSCOPE FM-SG Dummy UNIT
FM IN OUTPUT
Repeat step 1 several times
DC EVM
FM-SG
MHz OUT
AC EVM
OSCILLOSCOPE
EXT
OUT
VTVM VR03
OUT
UNIT FM AM GND TP11 GND UNIT
OUTPUT terminal FM ANT
STEREO MODULATOR
13
14
|
|
|
> |
|
