|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
The manual is well organized and is easy to read. The chapters are following normal way to proceed.
;
This scanned manual is well done in that most all the pages except for one is straight and clear- the way I would do them. One page was upside down but that happens. For the money that is charged on this site you get a pretty good deal. Now with complex repairs, I still prefer to us paper manuals which I have to buy at stereomanuals but the one I got here was much less than the $45 he was charging but this is a larger than normal manual for three different units. I am a picky manual user because I have used original manuals from Sony and Teac.
;
Very useful service manual, was exactly what i needed.Good quality,reasonable price.Thank you.
;
Acurate informations inside the SM and I could repair my old Sansui SC-3330 without any problems. Thanks.
;
I used it to repair a NAD 7030, but unfortunately, the 7045 is different !
But documentation was useful.
CUC 2030 / 2030 N / 2040 N / 2040 India
Abgleich / Alignment
D Abgleich
1. Chassisplatte
Me�geräte: Tastkopf 10:1, Farbbildgenerator, Spektrumanalyser oder HF-Millivoltmeter Servicearbeiten nach Austausch bzw. Reparatur: - Tuner: Abgl. 1.3
Abgleich 1.3 Tuner-AGC
Vorbereitung Spektrumanalyser oder HF-Millivoltmeter symmetrisch an Tunerkontakt 10, 11. Senderbild oder Generator über die Antenne einspeisen, 70�80dBµV.
Abgleichvorgang
Mit den Tasten "z -" oder "+ g" 102dBµV (360mVss) einstellen. Ersatzweise wird ohne Spektrumanalyser oder HF-Millivoltmeter mit den Tasten "z -" oder "+ g" das Bild so abgestimmt, da� es gerade zu rauschen beginnt. Dann Dialogzeile "AGC" über " " (DIALOG CENTER) �> "OK" soweit zurückstellen, bis das Bild wieder rauschfrei wird. �> SERVICE �> "OK" �> Service Code "8500" �> aufrufen. Dialogzeile "End" mit "with mem" beenden.
Hinweis:
Es werden in den Chassis CUC 20xx TDA 8843/8375 bzw. TDA 8843-N2/8844-N2 eingebaut. Bei dem Typ TDA 8843-N2/8844-N2 ist ein PLLDemodulator integriert und somit entfällt der AFC-Abgleich im Service Menü. Achtung! Nach einer Reparatur bzw. Wechsel des NVM (IC82005) mu� kontrolliert werden, ob der NTSC Quarz 3,58MHz bestückt ist. Bei nicht bestücktem Quarz, mu� über das Service Menü der Menüpunkt "NTSC 3,6" auf "aus" gestellt werden. �> OK �> SERVICE �> OK �> Service Code "8500" �> NTSC 3,6 "aus" und das Menü mit "with mem" verlassen
GB
Alignment
1. Chassis Board
Measuring instruments: 10:1 test probe, colour video generator, spectrum analyser or RF millivoltmeter. Service works after replacement or repair of the following modules: - Tuner: alignment 1.3
Alignment 1.3 Tuner AGC
Preparations Spectrum analyser or RF millivoltmeter symmetrical to tuner contact 10, 11. Feed in a standard test pattern or generator via the aerial, 70�80dBµV. Call up the dialog line "AGC" via " " (DIALOG CENTER) �> "OK" �> SERVICE �> "OK" �> Service Code "8500".
Alignment Process Adjust 102dBµV (360mVpp) with button "z -" or "+ g". Alternatively, without using a spectrum analyser or RF millivoltmeter, adjust the picture with button "z -" or "+ g" so that noise just appears on the screen. Then reset until the picture is again free of noise. Dialog line "End", terminate "with mem".
Note:
The CUC 20xx chassis is fitted with TDA 8843/8375 or TDA 8843-N2/8844-N2. Type TDA 8843-N2/8844-N2 has an integrated PLL demodulator so that the AFC needs not to be adjusted via the Service Menu. Attention! After repair or replacement of the NVM (IC82005) it is to be checked whether the NTSC 3.58MHz quartz is fitted. If this quartz is not inserted the menu option "NTSC 3.6" in the Service Menu must be set to "off". �> OK �> SERVICE �> OK �> Service Code "8500" �> NTSC 3.6 "off" and leave the menu with "with mem".
GRUNDIG Service
5
|
|
|
> |
|