|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
PART NAMES & FUNCTIONS
10) PITCH SLIDER Use this to change the speed of the platter when the PITCH button is lit. 11) HEADSHELL LOCKING NUT Attach the headshell by inserting into the front end of the tone arm, then turn the locking nut clockwise with the head shell firmly held horizontally. 12) TONE ARM This is a fully manual tone arm. To start playback, gently place the stylus on the record using the headshell finger support. Do not drop the stylus onto the record as it may cause damage to the diamond tip and to the record. 13) PITCH ON/OFF The ON setting will allow use of the pitch adjust. When set of OFF, the pitch control will be locked at 0%. 14) TONE ARM BASE The tone arm base includes the height adjustment, tone arm rest. See �tone arm and cartridge settings� for proper adjustments. Note: No Anti-Skate is needed on straight tonearms. 4) PLATTER REVOLUTION SPEEDS (rpm) 33 rpm � Press 33 45 rpm � Press 45 78 rpm � Press 33 and 45 buttons simultaneously. To return to 33 or 45-rpm play mode, just press the desired button. 5) HEASDHELL When installing a phonograph cartridge, refer to the installation instructions supplied by the cartridge manufacture. 6) TAGRET LIGHT Press the button to light up the stylus. To retract the light, press down on the light itself. 7) REVERSE This button is used to reverse the direction of the platter rotation. 8) PITCH SELECT Press the button to switch between +/-8%,+/-16%, or +/-25% pitch range. 9) PITCH BEND The pitch will increase/decrease by up to 6% while the pitch bend minus button is pressed. 15) COUNTERWEIGHT Use this to balance the tone arm and to adjust the stylus pressure. 16) HEADSHELL HOLDER This is used to place extra headshell during a performance for quick access. 17) OUTPUT This is the standard analog output (RCA jacks) which can be connected to a phono input on any DJ mixer. 18) GND Ground wire connection post 19) POWER SETICH This switch turns the power on or off, including the motor and audio signal. 20) POWER CORD CONNECTOR Used to connect the included power cord.
1) STROBE DOTS The dots around the edge of the platter are used in conjunction with the light located inside the motor ON/OFF switch. While the platter is in rotation, the dots help to indicate the speed of rotation. The speed is lower than the displayed speed (33,45,78) when the dots are flowing to the right. It is higher than the displayed speed (33,45,78) when the dots are flowing to the left. When the strobe is stopped, the platter is rotating at the displayed speed. 2) MOTOR ON/OFF SWITCH As opposed to analog turntables, this is not the power switch. This switch only turns on or off the motor. Rotate clockwise to turn on the motor. The platter will not start spinning until the start/stop button has been pressed. Rotate counter-clockwise during playback (off position) for a slow winding down effect. 3) START/STOP Press this button to start or stop the platter.
|
|
|
> |
|
