|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
 ;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
;
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
;
Very nice to have! Now it is no problem to understand how it is put together.
Helps me a lot.
;
good scans, all is clear. all pages in order. recommended
Multi Channel Surround Setup
x Center speaker size (CENTER) Initial setting : LARGE � If you connect a large speaker that will effectively reproduce bass frequencies, select �LARGE�. Normally, select �LARGE�. However, if the front speakers are set to �SMALL�, you cannot set the center speaker to �LARGE�. � If the sound is distorted, or you feel a lack of surround effects when using multi channel surround sound, select �SMALL� to activate the bass redirection circuitry and output the center channel bass frequencies from the front speakers (if set to �LARGE�) or sub woofer. *1 � If you do not connect a center speaker, select �NO�. The sound of the center channel will be output from the front speakers.*2 x Rear speaker size (REAR) Initial setting : LARGE � If you connect large speakers that will effectively reproduce bass frequencies, select �LARGE�. Normally, select �LARGE�. However, if the front speakers are set to �SMALL�, you cannot set the rear speakers to �LARGE�. � If the sound is distorted, or you feel a lack of surround effects when using multi channel surround sound, select �SMALL� to activate the bass redirection circuitry and output the rear channel bass frequencies from the sub woofer or other �LARGE� speakers. � If you do not connect rear speakers, select �NO�.*3
z About speaker sizes (LARGE and SMALL)
Internally, the LARGE and SMALL settings for each speaker determine whether or not the internal sound processor will cut the bass signal from that channel. When the bass is cut from a channel, the bass redirection circuitry sends the corresponding bass frequencies to the sub woofer or other �LARGE� speakers. However, since bass sounds have a certain amount of directionality, it best not to cut them, if possible. Therefore, even when using small speakers, you can set them to �LARGE� if you want to output the bass frequencies from that speaker. On the other hand, if you are using a large speaker, but prefer not to have bass frequencies output from that speaker, set it to �SMALL�. If the overall sound level is lower than you prefer, set all speakers to �LARGE�. If there is not enough bass, you can use the equalizer to boost the bass levels. To adjust the equalizer, see page 40.
Hooking and Setting Up the Speaker System
x Rear speaker position (REAR PLACE)* Initial setting : BEHIND This parameter lets you specify the location of your rear speakers for proper implementation of the Digital Cinema Sound surround modes in the �VIRTUAL� sound fields. Refer to the illustration below. � Select �SIDE� if the location of your rear speakers corresponds to section A. � Select �MIDDLE� if the location of your rear speakers corresponds to section B. � Select �BEHIND� if the location of your rear speakers corresponds to section C. This setting only effects the surround modes in the �VIRTUAL� sound fields.
z *1~*3 correspond to the following Dolby Pro Logic modes
*1 NORMAL *2 PHANTOM *3 3 STEREO
90° A 60° B C 20° 30° C B A
20
|
|
|
> |
|
