|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I liked the product. I would use their sevices again.
 ;
I Recently purchased yet another Service Manual from Owner-Manuals.com, this time for a Sony EVS700ES/UB Videocassette Recorder. The Manual was available for upload within two hours and is an Extremely Good copy, as some of this I was able to enlarge to get even better detail.
Once Again, Very happy with the result!
;
A good and useful manual. With these, We was abled to isolate and pin point the component that was causing the problem. The total time spent in troubleshooting is very much reduced.
;
The quality of the manual is top. The transfer worked perfect and fast.
No problems at all. Recommendable
;
Very good service for get any documentation. Fast and perfect quality.
[Aging Mode] � Execute only if connected to the HTC-NX1. This mode can be used for operation check of CD section and tape deck section. CD section and tape deck section work in parallel. � If an error occurred: The aging operation stops only an error occurred sections and display then status. � If no error occurs: The aging operation continues repeatedly. Procedure: 1. Set disc in DISC5 tray. 2. Load the tapes into the decks A and B respectively. 3. Press the [PLAY MODE] button to set the �ALL DISCS� mode, and press the [REPEAT] button to �REPEAT� off. 4. Press the [CD] button to select the function �CD�. 5. Press three buttons of [ENTER] , [POWER SAVE/DEMO] , and [TUNER BAND] simultaneously. 6. The aging mode is activated, if the indicator of disc tray number on the liquid crystal display is blinking. 7. To release from the aging mode, press the ?/1 button to turn the power OFF and operate the cold reset. (Refer to the �MC Cold Reset�) 1. Display at the Aging Mode � Display operating state of CD section and tape deck section alternately. � If an error occurred, stop display which that section. 2. CD Section � Display at the aging mode is the same as the normal operation. � The sequence during the aging mode is following as below. Aging mode sequence (CD section) :
� Display at an error occurred 1) Display of the error count (1) Press three buttons of [ENTER] , [POWER SAVE/DEMO] , and [GROOVE] simultaneously. (2) Display of the error count following as below. Display
EMC**EDC**
Notes: EMC**: The number of mechanical error. EDC** : The number of no disc error after chucking the disc.
2) Display of mechanical error Display
E**M##$$&&
Notes: ** : The number of mechanicalbutton to changes next error display) error.(�00� is latest one) (Press the [PLAY MODE] ## : Not used. $$ : Loading error. (Second figure is not used) D : The error in the midst of close at the except mechanical trouble. E : The error in the midst of open at the except mechanical trouble. C : The error in the midst of chuck up at the except mechanical trouble. F : The error in the midst of EX-open at the except mechanical trouble. &&: Loading error. (Second figure in not used) 1:The error in the midst of chuck up. 2:The error in the midst of chuck down. 3:Time up of EX-open 4:Time up of EX-close.
Open the disc1 tray
3) Display of no disc error Display
Disc5 chucking
E**D##$$&&
Disc5 TOC read
Notes: ** : The number of mechanical error.(�00� is latest one) (Press the [REPEAT] button to changes next error display) ##: 01: Focus error 02: GFS error 03: Set up error $$: 00: No disc error when does not chucking retry. 02: No disc error when chucking retry to completion. &&: The state when judged no disc error. (Second figure is not used) 1:Stop 2:Set up 3:TOC read 4:Access 5:Play 6:Pause 7:Manual search (Play) 8:Manual search (Pause)3. Tape Deck Section
Disc5 play track1 for 2 seconds
Disc5 play last track for 2 seconds
9
|
|
|
> |
|
