|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Impressively thorough. Even the simple operators manual helped me "fix" one of the 2 CD players in the unit. This unit reads CD's from the top so they should be installed in the magazines "upside down" from typical CD players. The CD player service manual helped me unjam a stuck carriage because somebody transported the box laying down loaded with CD's. A little lens cleaning & the player now works well! Thanks for you help at a great price! Joe
;
I was skeptical at first but later found the manual to be good quality for the price. It took a couple hours to receive the email with the download link, well worth the wait. Thanks.
;
very helpful, I could not have cleaned motherboard and replaced the main fan without it
 ;
Good manual, schematics nice and clear with good quality scanning. Woul dhave been nice to have immediate access after purchasing though.
;
I was very glad recieving the service manal from You. Manuals were delivered promptly and were correct as advertised. A complete and very usefull service manual with all details. Thank you!
3-16. Crescent Slide
1. Refer to Section 3-2 and remove the mechanism unit. When you do this, make sure the mechanism is in EJECT mode. 2. Refer to Section 3-3-1 and remove the cassette mechanism assembly. 3. Refer to Section 3-7-2 and remove the capstan brake assembly. 4. Refer to Section 3-12-4 and remove the T soft brake assembly.
A 4 Crescent slide 6 Hole B 1 Screw
2 Crescent mounting
3 Clamp 0 Hole
8 Hole
C
5. Refer to Section 3-13-1 and remove the T brake act slide. 6. Refer to Section 3-12-1, then remove the reel belt and the reel pulley. 7. Refer to Section 3-15, then remove the wheel gear 2 and the main cam. 8. Refer to Section 3-13-2, then remove the wheel gear 1 and the brake control lever. 9. Remove the two screws 1, then remove the crescent mounting 2. 10. Remove the clamps 3, then raise the right end of the crescent slide 4 slightly. Slide the crescent slide 4 to the right until it comes away from the clamp 5, then remove it. Assembly Notes: 1. Apply grease (VHJ-0100) to the points A, B, C and D in Fig. 3-16-1, and to the crescent slide 4 shown in Fig. 3-16-2. 2. Before fitting the crescent slide 4, refer to Section 313-3 and align the arrow on the S brake act slide with the arrow on the mechanism chassis. Then refer to Fig. 3-17-3 and check that the S load gear and the T load gear have completed tape unloading. 3. When assembling the parts, raise the right side of the crescent slide 4 slightly, and keeping it in this position, slot the left side into the clamp 5, then align the hole 6 with the hole 7 in the mechanism chassis. When you do this, check that the hole 8 is aligned with the pin 9 on the BT spring lever assembly, and that the hole 0 is aligned with the pin !- on the S brake act slide, before pressing the crescent slide 4 into place. Check that the clamps 3 and 5 are engaged. 4. After assembly, check that each lever and each brake is working properly.
D 7 Hole 5 Clamp
9 Pin !- Pin
Fig. 3-16-1
Apply grease to the areas shown in � The places marked by dots should be greased particularly generously.
Grease the sides
Grease the teeth
Crescent slide
Fig. 3-16-2
SVT-RA40/RA168
2-29
|
|
|
> |
|
