|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent, fast delivery, excellent product. Good luck!
;
This manual is for the usa model only. But it is clear
, accurate and comprehensive, including board layouts and schematics.
I found it extremely useful for my mitsubishi dp-86da, but the same diagram would also work for the realistic lab5000 and hi fi 80. Thanks.
;
Great to have extra resources for Service Manuals, Now days you can really not trouble shoot efficiently without one , Wayne at IRIONS TV & ELECTRONICS REPAIR Clearwater , Fl. 33755 727-446-7955
 ;
For five bucks you can barely buy a hamburger. Or for the same five bucks you can buy a service manual. Much more useful. (and better for your health, depending on where you buy your hamburgers).
Yes, there are free manual sites out there, but if they don't have what you want, you have to pay.
And five bucks isn't much. Not for full specs, schematics and adjustment and parts replacement procedures.
My only criticism is that grayscale illustrations aren't well rendered, but I've seen worse.
Schematics and text are clear.
I'll be happy to purchase from here again.
Mike
[email protected]
;
Impressively thorough. Even the simple operators manual helped me "fix" one of the 2 CD players in the unit. This unit reads CD's from the top so they should be installed in the magazines "upside down" from typical CD players. The CD player service manual helped me unjam a stuck carriage because somebody transported the box laying down loaded with CD's. A little lens cleaning & the player now works well! Thanks for you help at a great price! Joe
1
2
3
4
7.3 AMP BLOCK TROUBLE SHOOTING
The repair flow of the AMP section
A
PowerON After 4 seconds Level is low. A signal from CN481. (Sound from the speakers) no output no Go to SMPS part output Level is low. yes Check the screws OK of D AMP ASSY. Check soldering of IC421,441(B-2) Waveform is not normal.
The LED lights. yes
B
CrossOver 50Hz?
The speaker relay is on. yes Control Assy Input, D AMP Assy yes
no
A
Turn to Bypass and try again.
The 8-pin IC is hot.
no
Solder shorting? no yes
SMPS Assy Voltage of IC32? Less than [ 10V ]
Check other symptoms.
C
Replace the hot IC, since it is no longer serviceable.
Solder correction
Replace IC32.
'+''-' of multi-meter is reverse.
Cases other than 2�4 below. 1
A
D
Check the resistance between G and S of the FETs (Q421, 431, 441, and 451) with the multimeter. "+" is assigned to G and "-" is assigned to S for the multimeter. Multi-meter : ADVANTEST TR6847 or equivalent FET : IRFB23N15D 2 30k� to 40k� 1k to 10k 3 0 to 1k 4
All FETs are O.K.
All FETs are O.K.
FET has been broken.
E
Check soldering at IR2011S (IC421, IC441)
Replace IR2011S (IC421, IC441)
Replace IR2011S located on the same side as the FET with low resistance.
Everything is all right, except for the waveform (resistance of R471 and 472 is 10 ohms or more). Accidental failure mode Everything is all right, except for the relay not being turned on. Although the VOL is minimum, there is output from CN481.
F
Replace R471 and R472 with new ones. Replace Q506 and Q507 with new ones. Solder shorting of VR3141 of the CONTROL Assy.
44
1 2
S-W1EX
3 4
|
|
|
> |
|
