|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is a good quality scan of the Operation & Maintenance (Service) Manual for the PAL version of this high-band broadcast umatic, BVU-800P
All schematics and lineup procedures appear to be included in this one manual AFAICT.
The file size is just over 113 MB which gives an idea of the quality and number of pages.
All of the schematics, which contain some fairly small print, are easily readable when you zoom into the page.
John Thompson, Newcastle Upon Tyne, England.
;
Good quality, all schematics of few of models. There is also short form of user manual and regulation manual.
;
Perfect copy of the service manual. you can enlarge every page, and it comes up
with all details.
;
It´s very very nice manual with all, what i need. Original in good quality. Very fast business. Very much thanks...
;
Purchased the manual that I was looking for at a great price and could download it easily.. Great service experience and for future purchases I plan to use the site.
Thank you very much
SECAM CHROMA ADJUSTMENT
NO. Adjustment part Adjusting procedure and conditions 1 BELL FILTER f0 1 Receive Oi-5CH(SECAM colour bar). (SCM BELL) 2 Select the "SCM BELL" fo adjustment mode. I2C bus 3 Connect the oscilloscope to TP901 of main. adjustment (TP2901 in VCJ unit) Range : 10mV/Div. (AC) Sweep time: 20µsec/Div. (10:1 probe is used.) 4 Vary the bell filter data to align the waveform to be the nearest to that in Fig. 5 (b). (Arrange the level to gain the whole balance.) Waveform and others
SOUND LEVEL ADJUSTMENT
NO. Adjustment part Adjusting procedure and conditions 1 SUB SOUND 1 Receive E-12ch (PAL colour bar). Signal con(SUB VOL) tent: 400Hz 100% Mod. (I2C bus 2 Connect the probe of the meter to (SI) conadjustment) nector. (See Note) 3 Select "SUB VOL" in the service mode. 4 Adjust the sub-sound data to make the meter indicate 8.5Vrms (at L-ch). Adjustment value : 8.5 ± 0.4Vrms Waveform and others Note: * SPATIALIZER ..... OFF * S-Normal state * S-VOL ................ Max * S-BOOSTER ...... OFF
adjust
Fig. 5( a)
Fig. 5 (b) * To be at the same levbel. 2 SECAM black level R-Y/B-Y (R-Y and B-Y) I2C bus adjustment 1 Receive Oi-5CH(SECAM colour bar). 2 Select SECAM black level adjustment "R-Y" mode. 3 Connect the oscilloscope to TP802 (TP2804 in VCJ unit) of the main. Range: 10mV/Div. Sweep time: 20µsec/Div. (10:1 probe is used.) 4 Vary R-Y data to minimize the offset between the non-signal line and signal line as shown in Fig. 6 (b). 5 Select SECAM black label adjustment "B-Y" mode. 6 Reconnect the oscilloscope to TP803 (TP2805 in VCJ unit) of the main. The conditions are the same as in Item (3). 7 Vary B-Y data to minimize the offset between the non-signal line and signal line as shown in Fig. 7 (b). Fig. 6 (b) 2 Noise mute check 1 Receive E-12CH (PAL colour bar). 2 Maximize the sound volume to verify that the sound is output from the speaker. Then, set the non-signal state. 3 At this time, verify that the audio mute operates. 4 After checking the operation, set the sound volume to be the minimum. Fig. 6 (a)
OFF SET
SIF (NICAM/IGR) ADJUSTMENT
NO. Adjustment part 1 VCO COIL T2300 (in the NICAM unit) Adjusting procedure and conditions 1 Receive E-69CH (PAL colour bar). (Set the receiving frequency at AFT OFF Ex. E-69=855.25 MHz.) 2 Connect the digital voltmeter to TP301 (in the main unit). 3 Verify that it is turned counterclockwise to 0V and clockwise to 5V, and adjust T2300 to make the DC voltage of TP2300 become 2.5 ± 0.1V in the range. <Single-unit adjustment> - For your Reference. Vcc 5 ± 0.1V IF input frequency 38.9MHz ± 10kHz Control it under these conditions.
OFF SET
Waveform and others
7
Fig. 7 (a)
Adjust T2300 to make the DC voltage of TP2300 (in the NICAM unit) become 2.5 ± 0.1V. After single-unit adjustment, check the practical setup. Align the receiving frequency to the select channel frequency. (AFT OFF) The checked TP301 in the main unit voltage must be 2.5 ± 1.0V. (Take care that ±1.0 is considered for the Vcc difference between the single unit and unit, Fo difference and so on, but is not the adjustment precision.)
SX68JF100
Fig. 7 (b)
7-1
7-2
|
|
|
> |
|
