|
Who's Online
There currently are 5743 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
A comprehensive Operating and Service Manual. All schematics are complete and easy to read. The PCB drawings and complete parts list are very helpful. I would definitely recommend this manual.
;
SCANNING OF HIGH QUALITY
VERY, VERY HIGH VELOCITY DOWNLOAD
VERY GOOD PRICE,
TRUE SATISFIED, THANKS
;
Genuine Toshiba owner's manual. Couldn't really ask for more. And written in understandable English in contrast to a few recent experiences I have had with manuals for other equipment other than Toshiba but made in China and written in "Chinglish"!
;
I purchased a vintage Sony mixer off eBay and within the hour was able to locate and purchase the manual for it.I mean really,where else can you find a manual for a product made in 1983!? It was easy to find and purchase/download the manual I needed.I will use this site again for other equipment I have! Great site!
;
manual de usuario perfecto y completo de buena calidad de impresion y muy detallado ideal !
7 Connecting the speaker system to the amplifier
Before connection� � Turn off the power to the amplifier before connecting the speaker system; otherwise, the speakers may be damaged. � The impedance of the speaker is 6 �. Before connecting it to your amplifier, check the speaker impedance range of your amplifier. If the impedance of this speaker is out of the speaker impedance range indicated on the amplifier, you cannot connect this system to the amplifier. � The maximum power handling capacity of the SX-LC33 is 120 W. Excessive input will result in abnormal noise and possible damage. � Be sure to turn down the volume level to prevent unwanted noise before performing following operations: � Turning on or off other components, � Operating the amplifier, � Tuning FM stations, � Fast-forwarding a tape, � Continuously reproducing high frequency oscillation or high pitch electronic sounds. � When using a microphone, do not aim it at the speakers or use it near the speakers; otherwise, the howling which occurs may damage the speakers. � Before replacing the cartridge, always turn off the power to the turntable; otherwise, the clicking noise may damage the speakers.
7 Connecting the speaker cord to the speaker
Connect the speaker cord to the speaker as follows.
1 Twist and remove the insulation at the end of each speaker cord before connecting.
2 Rotate the speaker terminal knob counterclockwise and fit the speaker cord into the groove. Then rotate the knob clockwise to secure the cord.
Tighten ª terminal (Red) · terminal (Black) Copper To the speaker ª terminal of amplifier To the speaker · terminal of amplifier Loosen
Silver
About speaker cords�to improve the sound quality
About the OFC cord The core wires of the supplied speaker cords are made of OFC (Oxygen Free Copper). This OFC cord enables high quality sound reproduction. When connecting the speaker cords Make sure to match the polarity (ª and ·); otherwise, the surround effect will become less effective. After connecting, check that the exposed cores are fully inserted into the terminal. When using other speaker cords Observe the following; � Buy thick speaker cords rather than thin cords, and make them as short as possible for connection. � Do not use long speaker cords; otherwise, the sound quality may deteriorate. � Use speaker cords of the same length for both left and right speakers. � Using a special speaker cord such as a litz wire, a coaxial cable, or a cord which has the specified connecting directionality may influence the sound quality.
Specifications
Type: 2-way 3-speaker bass-reflex type Magnetically-shielded type Speakers Woofer: 13.5 cm cone x 2 Tweeter: 1.9 cm dome x 1 Power handling capacity: 120 W Impedance: Crossover frequency: Frequency range: Sound pressure level: Dimensions (W x H x D): Mass: 6� 4 000 Hz 52 Hz to 80 000 Hz 89 dB/W�m 150 mm x 415 mm x 292.5 mm 8.0 kg
Design and specifications subject to change without notice.
3
English
Connection
|
|
|
> |
|