|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
A comprehensive Operating and Service Manual. All schematics are complete and easy to read. The PCB drawings and complete parts list are very helpful. I would definitely recommend this manual.
;
SCANNING OF HIGH QUALITY
VERY, VERY HIGH VELOCITY DOWNLOAD
VERY GOOD PRICE,
TRUE SATISFIED, THANKS
;
Genuine Toshiba owner's manual. Couldn't really ask for more. And written in understandable English in contrast to a few recent experiences I have had with manuals for other equipment other than Toshiba but made in China and written in "Chinglish"!
;
I purchased a vintage Sony mixer off eBay and within the hour was able to locate and purchase the manual for it.I mean really,where else can you find a manual for a product made in 1983!? It was easy to find and purchase/download the manual I needed.I will use this site again for other equipment I have! Great site!
;
manual de usuario perfecto y completo de buena calidad de impresion y muy detallado ideal !
Connection
7 Connecting the speaker system to the amplifier
Before connection� � Turn off the power to the amplifier before connecting the speaker system; otherwise, the speakers may be damaged. � The impedance of the speaker is 6 �. Before connecting it to your amplifier, check the speaker impedance range of your amplifier. If the impedance of this speaker is out of the speaker impedance range indicated on the amplifier, you cannot connect this system to the amplifier. � The maximum power handling capacity of the SX-LT55 is 150 W. Excessive input will result in abnormal noise and possible damage. � Be sure to turn down the volume level to prevent unwanted noise before performing following operations: � Turning on or off other components, � Operating the amplifier, � Tuning FM stations, � Fast-forwarding a tape, � Continuously reproducing high frequency oscillation or high pitch electronic sounds. � When using a microphone, do not aim it at the speakers or use it near the speakers; otherwise, the howling which occurs may damage the speakers. � Before replacing the cartridge, always turn off the power to the turntable; otherwise, the clicking noise may damage the speakers. � Use speaker cords as follows; � Buy thick speaker cords rather than thin cords, and make them as short as possible for connection. � Use speaker cords of the same length for both left and right speakers. � Do not use long speaker cords; otherwise, the sound quality may deteriorate. � Using a special speaker cord such as a litz wire, a coaxial cable, or a cord which has the specified connecting directionality may influence the sound quality.
Speaker cord (not supplied)
SPEA
RIGHT
7 Conventional connection
1 Loosen the knobs of the �FULL RANGE� terminals. 2 Fit the speaker cords into the grooves of the �FULL RANGE� terminals, then tighten the knobs to secure the speaker cords and short-circuit plates.
FULL RANGE terminals Short-circuit plate
LOW FREQUENCY LOW FREQUENCY (WOOFER ONLY) (WOOFER ONLY)
KERS
L
EFT
7 Bi-wiring connection
This speaker is bi-wireable. Comparing with the conventional connection, the bi-wiring connection makes the sound field larger, deeper, and richer.
1 Loosen all speaker terminal knobs and detach the short-circuit plates.
Short-circuit plates
7 Connecting the speaker cord
Connect the �INPUT� terminal of the speaker to the speaker terminal of the amplifier. Rotate the speaker terminal knob counterclockwise and fit the speaker cord into the groove. Then rotate the knob clockwise to secure the cord.
2 Connect the �FULL RANGE� terminals and �LOW FREQUENCY� terminals separately to the speaker terminals of the amplifier.
FULL RANGE terminals
LOW FREQUENCY terminals
(Red) (Black)
HIGH FREQUENCY
HIGH FREQUENCY
LOW FREQUENCY (WOOFER ONLY)
LOW FREQUENCY (WOOFER ONLY)
(Red)
SPEAKERS
RIGHT
EFT L
� Make sure to match the polarity (ª and ·); otherwise, the surround effect will become less effective.
Speaker cord (not supplied)
3
English
|
|
|
> |
|
