|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was very pleased with the manual I got for my amateur (ham) radio. Without it I could not figure out how to input and/or change the P/L setting on my radio. It drove me nuts as the radio was essentially useless. That all changed when my manual came. Then it took only minutes and I was done. Now my radio works fine. This is an exceptionally good resource as it's a very easy and user friendly download. Thank you very much! Dziękujemy za!
 ;
It answered my question, which was how to load the paper. I did notice that the very end of the manual was not visible.
 ;
The product manual I received was exactly what I was looking for, delivered painlessly at a very fair price. I can't ask for any more than that.
 ;
Very well done!!!!! congratulations. It was a bit longer than usual the wiating time even if it was on time (in 24 hours).
 ;
Last week I bought a second hand BAUKNECHT TRK4850 DRYER. It is a professional machine with many programs and switch options. I feared it would be a huge quest to find a manual. I was delighted when I found owner-manuals.com. After payment I received the file to download the next day already. The quality is great. I am very happy. Thanks!
but kindly the distributions of the operating programs not find in the owners manual,can you help me to understand the operating programs instructions thank you
Features
A Patented AccuControl System with Removable Guide Comb Attachment B Selected Hair Length Setting Window C 4 Length Settings D 3-Dimensional Rounded Chromium Steel Cutter Blades E On/Off Switch F Cleaning Brush Full Two-Year Warranty 60-Day Money-Back Guarantee Trimming Length Settings Table
Settings
#1 #2 #3 #4 �Stubble� Setting Short Medium Long
Resulting beard length
.06 in./1.5 mm .12 in./3 mm .2 in./5 mm .28 in./7 mm
Trimming For �Stubble� Look 1 Be certain Guide Comb is on Trimmer and use setting #1 to result in a �stubble� look. (fig. 9). Trimming Without Guide Comb Attachment Remove Guide Comb Attachment if you are:
� Defining hair lines � Trimming nape of neck � Removing single, unwanted hairs
1 Be certain Trimmer is in the OFF position. 2 Remove the Guide Comb Attachment by adjusting it to setting #4 and then pulling it off the Trimmer (fig. 10). Never pull off the Guide Comb Attachment by grasping the flexible top portion. Always pull off by the bottom part of attachment. 3 Switch the Trimmer ON. 4 Make well-controlled movements.Touch the hair lightly with the Trimmer (fig. 11). Replacing Guide Comb Attachment On Trimmer 1 Be certain Trimmer is in OFF position. 2 Replace Guide Comb Attachment until it �clicks� into position and adjust comb to the chosen setting.The Guide Comb Attachment can be placed on Trimmer only one way. If it does not fit properly, reverse it.
Cleaning
� Always switch Trimmer OFF before cleaning. � Do not use abrasives, scourers or liquids such
as alcohol, benzene, bleach or acetone to clean the Trimmer. � Never clean, remove or replace Guide Comb Attachment with motor ON. � Do not apply pressure to cutters. � Do not touch cutters with hard objects as this may damage them. � Do not use while bathing, showering or immerse the Trimmer in water or other liquids as damage to Trimmer may occur. During Use:
� If cut hairs have accumulated in the Guide
Comb area, turn Trimmer off, remove the Guide Comb Attachment by adjusting it to setting #4 and then pull it off Trimmer. Remove hairs by shaking and/or blowing. Once A Week: 1 Make sure the Trimmer is switched OFF. 2 Remove the Guide Comb Attachment. 3 Open the cutting unit by pushing it backwards (fig. 12 #1). 4 Clean the cutting unit and the inside of the Trimmer with the brush supplied (fig. 12 #2). 5 Close the cutting unit by pushing it back into place on the Trimmer until you hear a click (fig. 13).
Replacing The Cutting Unit
If your cutters become damaged or worn, do not continue using the Trimmer. Replace cutters immediately. 1 Open the cutting unit. 2 Remove the old cutting unit by pulling it upwards. 3 Place the two notches of the new cutting unit into the guiding slots (fig. 14 #1).
|
|
 |
> |
|