|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
;
I received the Manual in a timely manner and it was exactly what I needed.
This is a perfect copy of the Service Manual, The quality is great. I am very
happy. Thank you
;
exactly as they say. Within 24 hours the link to the pages and offcourse it was the right service manual. Super and thanks
 ;
The manual was exact the thing that was promised. My old car stereo is working again thanks to the information supplied.
ALIGNMENT PROCEDURE (T973)
A. DC OFFSET VOLTAGE The DC OFFSET between OFFSET Test Point and AGND must be controlled within 0+/-3mV. If it�s found to be out of this range, change the TL084BCD to get it meet the requirement. B. IDLING CURRENT The idling current at the final stage of the unit should be set to about 40mA+/-10mA. Adjust RV102 (As marked as �Idling Current ADJ� in the enclosed drawing below) to control the voltage between Idling current Test point 1 and 2 to be 8mV +/- 2mV. Preheat the unit for 10 to 15 minutes, and then readjust to 8mV +/- 2mV. (Please note: The idling current must be adjusted when all modules are assembled into the unit.) C. ISC SENSITIVITY Adjust Pot RV104 (as marked as �ISC SENS ADJ� in the below drawing) to get the voltage across �ISC SENS TEST POINT� and AGND to be 0mV+/-10mV. (Please note that the ISC should be adjusted when all modules are assembled into the unit. It�s not possible to get 0V +/-10mV if the modules are not assembled. D. THERMAL SENSE ADJUSTMENT The adjustment should be always done when the T973 is cool condition. (That means the temperature inside the unit should be almost same as the ambient temperature. Connector P208B that connects the transformer and power board should be removed to avoid that the Idling current to heat up the unit excessively) At ambient temperature of 25 C degree and when the unit is just turned on (still in cool condition), adjust the pot RV103 (as marked as �THERMAL SENS ADJ� in the below drawing) to get voltage across the THERMAL TEST POINT and AGND to be 750mV +/-10mV. While the ambient temperature is different, the voltage will vary as well. There is a relation between the temperature and voltage, that is; if the ambient temperature is 20 degree C, the voltage should be 850mV+/-10mV; if the ambient temperature is 30 degree C, the voltage should be adjusted to 650mV+/-10mV, etc. E. Fan Cut Off Point Adjustment Note: This Fan cut off function does not appear on PCB V10.0, V11.0 or MKII version but only appeared on PCB V12.0. Run the unit for all 7 channels at 1 kHz, 4ohms load, and 250mW output. Do this adjustment when the unit heats up, for example; run the unit at all 7 channels at 50W/4ohms for 10 minutes. Then adjust Pot RV201 on power supply board so the voltage at Pin14 of IC203 just changes from negative to positive (to get the fans just start turning). Then turn off the input signal and monitor if fans will stop within 30 seconds, then turn on the input signal again to see if the fans start turning immediately.
 $4.99 T973 NAD
Owner's Manual Complete owner's manual in digital format. The manual will be available for download as PDF file aft…
|
|
|
> |
|
