|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
 ;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
TCM-500DV SECTION 4 MECHANICAL ADJUSTMENTS
1. Clean the following parts with a denatured-alcohol-moistened swab: record/playback/erase head pinch roller capstan rubber belt 2. Demagnetize the record/playback/erase head with a head demag netizer. 3. Do not use a magnetized screwdriver for the adjustments. 4. The adjustments should be performed with the rated power supply voltage (3 V) unless otherwise noted. Torque Measurement
Mode FWD CQ-102C FWD Back Tension REV REV Back Tension FF, REW CQ-201B more than 4.91 mN�m (more than 50 g�cm) (more than 0.69 oz�inch) 0.05 � 0.49 mN�m (0.5� 5 g�cm) (0.007 � 0.069 oz�inch) input level output level Mic earphone �60dBs 16�, �20dBs Torque Meter Meter Reading 1.97 � 3.92mN�m (20 � 40 g�cm) (0.28 � 0.55 oz�inch)
SECTION 5 ELECTRICAL ADJUSTMENTS
Setting: � Supplied voltage: 3 V (DC) � Switch and control position VOL contorl (RV101) : mechanical center REC SPEED switch (S401) : normal (4.8cm/s) PAUSE switch (S601) : OFF SPEED CONTROL (RV201) : center click VOR switch (S402) Regulation Level : OFF Tape Speed Adjustment Mode: playback
test tape WS-48A (3 kHz, 0 dB) 16 � set
+ �
Ver 1.2
frequency counter
EAR jack (J102)
Procedure: 1. Set [REC TIME] switch (S401) to NORMAL (4.8 cm/s) position, and playback the tape (WS-48A) . 2. Adjust RV602 so that frequency counter reading becomes 3,010 Hz. 3. Set [REC TIME] switch (S401) to DOUBLE (2.4 cm/s) position. 4.Playback the tape from the beginning for two minutes, then adjust RV601 so that frequency counter reading becomes 1,505 Hz.
Test Tape
Type WS-48A Signal 3 kHz, 0 dB Used for tape speed adjustment
Tape Tension Measurement
Mode FWD Tension Meter CQ-403A Meter Reading more than 50 g (more than 1.76 oz)
0 dB=0.775 V Confirm that deflection of the frequency counter reading between the beginning and the end of tape is within 2% (NORMAL: approx. 60 Hz, DOUBLE: approx. 30 Hz) .
Adjustment Location: � MAIN BOARD (Conductor Side) �
RV601 Tape Speed Adjustment (Double Speed)
RV602 Tape Speed Adjustment (Normal Speed) 20 11
IC601
1 10
7
7
|
|
|
> |
|
