|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Perfect for my use.Could have better pictures,but otherwise perfect ;)
 ;
This is one of four manuals I have downloaded recently.
Purchase was very straight forward and the authorising email arrived in about 4 hours.
The quality of the scan is good. Print is clear and square to the page edges.
;
Exactly as advertized. High quality digital copy of the Nak 610 user manual. Easy download and access. Highly recommended.
;
The manual was exactly what I wanted and I found it nowhere else. Thanks!
;
Having purchased a 1994 Kenwood music system from a Charity shop in 2013 (it was a high end product in its day), I found myself not quite knowing where to plug in what, and how to do this, that and the next thing. I needed a Manual, and after failure with another online 'Manual provider' I found Owner Manuals dot com. Well, I wasn't sure, but it was only $5, and if things didn't work out, I wouldn't have lost much...
But things DID work out. After paying my childrens inheritance money, $4.99, I was sent a Manual for my Kenwood System very quickly. Alas, it was in German, and being Scottish, I could not read it or get my system in order from it...a rapid email to them brought the English Manual in short order, and my retro-system was and IS up and running in it's regulation settings.
I am very grateful to http://www.owner-manuals.com for their quick service and for even having such an obsolete Manual in the first place! If you need a Manual for ANYTHING, try here first. I wouldn't be surprised if I bought a 1928 Marconi radio, and got the user Manual for THAT here too!
Top marks.
John Copeland
Glasgow
Scotland
Amplifier settings
Adjusting crossover
When using a small speaker with weak bass as a front, center, or rear speaker, you can redirect bass audio to the sub-woofer. Select a crossover frequency to match the size of the small speaker being used. � When you use the supplied speakers with this system, set the crossover frequency as follows: CROSSOVER: 200Hz
Adjusting dynamic range
You can compress the dynamic range. This may be used when you play back surround effects at night. This function work only for the program recorded in Dolby Digital. � The initial setting of D. RANGE COMP is �MID�.
1 2 3
Press SETTING. Press the 5/� cursors until �CROSSOVER� � appears on the display window.
� After a while, the current setting appears.
1 2 3
Press SETTING. Press the 5/� cursors until �D. RANGE � COMP� appears on the display window.
� After a while, the current setting appears.
Within 5 seconds, press the 2/3 cursors to 3 select the crossover frequency.
Pressing the button changes the crossover frequency as follows: j 200Hz j 120Hz j 100Hz j Crossover frequency 100Hz 120Hz 200Hz* Speaker diameter approx. 10 cm (4�) approx. 8 cm (3-3/16�) approx. 4 cm (1-5/8�)
Within 5 seconds, press the 2/3 cursors to 3 select the setting.
Pressing the button changes the dynamic range compression as follows: j MAX j MID j OFF j MAX: The dynamic range is fully compressed. MID: The dynamic range is compressed a little. (Initial setting) OFF: The dynamic range is not compressed.
* Select when the supplied speakers with this system are used.
To exit power amplifier setting mode
Press SETTING again.
To exit power amplifier setting mode
Press SETTING again.
Note:
� To enjoy original sound, you should set to �MID� or �OFF�.
Note:
� When �LARGE� is set for the front, center and rear speakers, you cannot adjust CROSSOVER.
Adjusting LFE attenuator
When bass sound is distorted while playing back the program recorded in Dolby Digital or DTS surround, you can lower the sound level through the LFE attenuator. � Normally, LFE ATT should be set to �OFF�.
1 2 3
Press SETTING. Press the 5/� cursors until �LFE ATT.� � appears on the display window.
� After a while, the current setting appears.
Within 5 seconds, press the 2/3 cursors to 3 select �ON� or �OFF�.
Pressing the button toggles between �ON� and �OFF�. ON: Select when bass sound is distorted. OFF: Select to turn off LFE ATT. effect.
English
To exit power amplifier setting mode
Press SETTING again.
52
|
|
|
> |
|
