|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual was exact the thing that was promised. My old car stereo is working again thanks to the information supplied.
;
I PURHASED THIS PRODUCT BECAUSE I WAS HAVING PROBLEMS WITH MY CDR20 HARMAN KARDON RECORDER. WHICH I PURCHASED NEW 12 YEARS AGO. AFTER REVIEWING THE MANUAL, I WAS ABLE TO ADJUST THE TENSIONER IN THE SYSTEM. WORKS LIKE A CHAMP!.
SAVED ME AT LEAST 100.00 WHICH WAS WHAT A SERVICE REPAIR STATION WANTED. GREAT MANUAL EASY TO READ. SPECIALLY AFTER I PRINTED THE PAGES WHICH DEALT WITH MY RECORDER. THANKS A LOT!!!!!!!!
 ;
You can fully trust on this one!
All the schematics are very crear an in one piece per page
;
I have never bought a service manual which is as competely readable as this althogh it was a scanned pdf. Thank you for this succesful manual also cheaper than other sites.
;
Thanks for a very good and readable servicemanual. Just what I needed as a "dinosaur technician". I really recommmend this site and will come back.
Åsbjörn
TK-2207
DISASSEMBLY FOR REPAIR / 维修��
â� Removing the case assembly from the chassis.
1. Remove the volume knob z and channel knob x. 2. Remove the two screws c. 3. Lift and remove the chassis from the case assembly (Use a flat-blade screwdriver to easily lift the chassis.)
â� æ��å�¸æ�ºå£³
1. å�¸ä¸�é�³é��æ��é�® z å��ä¿¡é��æ��é�® xã�� 2. å�¸ä¸� 2 个è�ºä¸� cã�� 3. æ�¬èµ·æ�ºæ�¶ vï¼� å°�å�¶ä¸�æ�ºå£³å��离å��å�ºã�� (使ç�¨ä¸�å�å½¢è�ºä¸�å��ä¼�æ¯� è¾�容æ��æ�¬èµ·æ�ºæ�¶ã�� )
1 2
v.
3 3 4
â� Removing the TX-RX unit from the chassis.
1. Remove the packing b from the SP / MIC jack of the TXRX unit. 2. Remove the eleven screws n fixing the TX-RX unit. 3. Remove the fixing bracket m of the SP / MIC. 4. Remove the solder of the antenna terminal with a soldering iron ,. 5. Remove the solder of the positive terminal with a soldering iron .. Note: You can remove the TX-RX unit from the chassis without removing the solder at the positive terminal. However, in this case, you can not attach the packing (G53-160503) that is on the positive terminal to the chassis in assembling. So, it is advisable to remove the solder on the positive terminal first. 6. Remove the FPC from the flat cable connector /. 7. Lift and remove the TX-RX unit from the chassis �.
â� æ��å�¸ TX-RX å��å��
1. ä»� TX-RX å��å��ç�� SP / MIC æ��å�å�¸ä¸�æ©¡è�¶å�« bã�� 2. å�¸ä¸�å�ºå®� TX-RX å��å��ç�� 11 个è�ºä¸� nã�� 3. å�¸ä¸� SP / MIC é�¨ç��å�ºå®�æ�¯æ�¶ mã�� 4. ç�¨ç�µç��é��ç�«å¼�天线端å�ç��ç��é�¡ ,ã�� 5. ç�¨ç�µç��é��ç�«å¼�ç�µæ± æ£æ��端å�ç��ç��é�¡ .ã�� è¡¥å��说æ��â�¶è�½ç�¶ä¸�ç�«å¼�ç�µæ± æ£æ��端å�ç��ç��é�¡ä¹�å�¯ä»¥ä»�æ�ºæ�¶æ��å�¸ TX-RX å��å��ï¼�ä½�æ�¯ç»�è£�æ�¶ï¼�ç�µæ± æ£æ��端å�è¿�æ�¥ç��å�« ç��ï¼�G53-1605-03ï¼�ä¸�è�½å®�è£�å�°æ�ºæ�¶ã��å� æ¤ï¼�请å��ç�« å¼�ç�µæ± æ£æ��端å�ç��ç��é�¡ã�� 6. ä»�æ��å¹³ç�µç¼�è¿�æ�¥å�¨å�¸ä¸� FPC /ã�� 7. æ�¿èµ· TX-RX å��å�� â�¦ï¼�ä»�æ�ºæ�¶æ��å�¸ä¸�æ�¥ã��
6 7 6 6 6 6
8
6 6 6
10 11
5
9
7
|
|
|
> |
|
