|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It was helpful to get schematic with waveforms in important points and lot of service information. Manual is good quality, fast delivered. Of course it is hardcopy of paper one with all its disadvantages.
 ;
I want to give you a real heads-up for your desire to enable such people as I to acquire the information I need to maintain the older types of equipment such as this Akai HXA351W. You do a swell job with all the processes you have to perform so I can have a legible, thus usable
document which does not send me crazy trying to figure out the blurry text of a bad copy.
Very well done, Thomas.
;
This manual is very well presented and after printing out looks about as close to an original as I think you can get. The quality is second to none.
The content of the manual is comprehensive and I think it would be well suited to an audio repair professional which I'm not but I did find it very informative and helpful.
The cost of the manual is more than covered by the money I'll save when I change the keep memory battery now I have the relavant info.
Very pleased with my purchase and can recommend it wholeheartedly as I can other manuals I've downloaded from this site.
Regards
Limey Alex
;
Complete manual including mechanical part in good pdf quality. Shaded greys of the pcb due to pdf not perfect but usable.
;
Nice pdf file of the manual sent promptly. Thanks.
TK-782
OPERATING FEATURES /
" Auto Dial Programming
You can store the DTMF code and name, or erase it at the transceiver.
"
! To store a DTMF code
Press the [Auto dial programming] key to enter �Auto dial programming mode�. Select the desired memory number you wish to store. Press the [*] key to select the desired memory number (Enter auto dial memory name). Press the [*] key to store the memory name. Now, enter the DTMF codes you want to store. Press the [*] key to store the numbers. A beep sound confirms that the numbers are stored in the memory.
!
! To erase the stored DTMF code
Press the [Auto dial programming] key to enter �Auto dial programming mode�. Press the [#] key to enter �Auto dial clear mode�. Select the memory number you want to erase. Press the [*] key to erase the stored numbers and exit �Auto dial clear mode�.
!
" AUX A
If this key is pressed, �AUX� icon lights on the LCD and Horn alert port which is inside of the transceiver turns to the high level. If pressed again, the �AUX� icon goes off and the Horn alert ports turns to the lower level.
"
" AUX B
This function can be programmed when the voice scrambler board is not installed. If this key is pressed, an underscore (�_�) appears at the extreme right of the LCD and OPT port which is inside of the transceiver turns to the active level (low). If pressed again, the underscore disappears and the OPT ports turns to the deactive level (high).
"
" Channel Name
Press this key to switch between the �Channel name� and �Grp #/Ch #� for the display. If no channel name is programmed, the transceiver automatically displays the group #/ channel #.
"
" Channel Up/Down
When this key is pressed each time, the channel number to be selected is increased/decreased and repeats if held for one second or longer.
"
" Channel Entry
You can directly recall the channel using the numeric keypad without using the [Channel up], [Channel down]. To access the channel directly, enter 1 to 3 digit numbers, depending on the number of the programmed channels. For example, if the radio has 199 programmed channels (the maximum channel number is a 3-digit number) and you would like to recall channel 5, you must enter [0],[0],[5]. If the radio has 99 channels (2-digit number), you must enter [0],[5] to access channel 5.
"
6
|
|
|
> |
|
