|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
exactly as they say. Within 24 hours the link to the pages and offcourse it was the right service manual. Super and thanks
 ;
The manual was exact the thing that was promised. My old car stereo is working again thanks to the information supplied.
;
I PURHASED THIS PRODUCT BECAUSE I WAS HAVING PROBLEMS WITH MY CDR20 HARMAN KARDON RECORDER. WHICH I PURCHASED NEW 12 YEARS AGO. AFTER REVIEWING THE MANUAL, I WAS ABLE TO ADJUST THE TENSIONER IN THE SYSTEM. WORKS LIKE A CHAMP!.
SAVED ME AT LEAST 100.00 WHICH WAS WHAT A SERVICE REPAIR STATION WANTED. GREAT MANUAL EASY TO READ. SPECIALLY AFTER I PRINTED THE PAGES WHICH DEALT WITH MY RECORDER. THANKS A LOT!!!!!!!!
;
You can fully trust on this one!
All the schematics are very crear an in one piece per page
;
I have never bought a service manual which is as competely readable as this althogh it was a scanned pdf. Thank you for this succesful manual also cheaper than other sites.
TM-271A/271E
RESETTING THE TRANSCEIVER
Resetting the Tansceiver
If your transceiver seems to be malfunctioning, resetting the microprocessor may solve the problem. The following 2 reset modes are available. When performing the reset, you may lose memory data and stored information. Back up or write down important data before performing the reset.
â� VFO Reset
This resets the transceiver parameters excluding the DTMF Memory, the Memory channel contents, and the Call channel contents. There are two methods available for resetting the transceiver. Note : Menu No. 7 (P.VFO) and Menu No. 10 (OFFSET) return to the factory default values.
â� Initial Settings
The factory defaults for the operating frequencies are as follows. Transceiver : 144.000MHz The Memory Channels have no data stored. The Weather Radio frequency (AL channel) is restored as 162.550MHz (K market model only). The Call Channel and frequency step size default values. Note : When in Channel Display Mode or while Key Lock is activated, you cannot perform VFO reset or Full reset.
� VFO Reset Method 1:
1. With the transceiver power OFF, press [VFO]+[ ] (Power). � The VFO reset confirmation message appears.
â� Full Reset
This resets all transceiver parameters to the factory default values. There are two methods available for resetting the transceiver.
2. Press [VFO]. � �SURE ?� appears. � Press any key other than [VFO] to cancel. 3. Press [VFO] again to reset the transceiver. � �WAIT� appears momentarily.
� Full Reset Method 1:
1. With the transceiver power OFF, press [F]+[ ] (Power). � All indicators light momentarily, followed by the full reset confirmation message.
� VFO Reset Method 2:
1. Press [F], [MENU] and turn the Tuning control to select Menu No. 99 (RESET). 2. Press [MENU] and turn the Tuning control to select �VFO�. 3. Press [MENU]. � �SURE ?� appears.
2. Press [F]. � �SURE ?� appears. � Press any key other than [F] to cancel. 3. Press [F] again to reset the transceiver. � �WAIT� appears momentarily.
� Press any key other than [MENU] to cancel. 4. Press [MENU] to reset the transceiver.
� Full Reset Method 2:
1. Press [F], [MENU] and turn the Tuning control to select Menu No. 99 (RESET). 2. Press [MENU] and turn the Tuning control to select �FULL�. 3. Press [MENU]. � �SURE ?� appears.
� Press any key other than [MENU] to cancel. 4. Press [MENU] to reset the transceiver. � �WAIT� appears momentarily.
19
|
|
|
> |
|
