JVC TM-H1950CGE
Owner's Manual

TM-H1950CG

CONTROLS AND FEATURES
FRONT VIEW
<Front Panel>
1
CHROMA CONTRAST VOLUME/SELECT MENU UNDER SCAN COLOR OFF BLUE CHECK ASPECT A B C SLOT D

POWER

15
PHASE BRIGHT INPUT SELECT

2
CHROMA CONTRAST VOLUME/SELECT MENU
UNDER SCAN COLOR OFF BLUE CHECK ASPECT
A B C SLOT D

3

4

5

6

7

8

9 10 11

12

13 14

POWER

TM-H1950CG

PHASE

BRIGHT

INPUT SELECT

(Front view of TM-H1950CG shown)

1 Tally lamp
Lights when the tally control signal is ON. The tally control signal is input through the REMOTE (external control) remote terminal. For details, refer to Page 18.

8 Blue Check button [BLUE CHECK]
Cuts red and green signal components. Only blue signal components are shown. Press the button again to restore the normal image. When selected, this button lights.

2 Chroma/Phase button [ CHROMA/ PHASE]
Press this button to activate the picture color density adjustment mode or picture hue adjustment mode. Each time you press the button, the adjustment item changes. Picture color density f Picture hue Adjust the value with the VOLUME/SELECT buttons 4. Also used as a control button in the menu function mode.

9 Aspect button [ASPECT]
Press this button to change the aspect ratio from 4:3 to 16:9.

10 Input A (VIDEO) button [INPUT SELECT A]
Selects the video and audio signals input to the VIDEO A * and AUDIO A q terminals on the rear panel. The button lights when selected.

3 Contrast/Brightness button [CONTRAST / BRIGHT ]

11 Input B (VIDEO Y/C) button [INPUT SELECT B]
Selects the video and audio signals input to the VIDEO B ( or VIDEO B (Y/C) ) and AUDIO B w terminals on the rear panel. The button lights when selected. Note: � The VIDEO B terminals include a video terminal (BNC connector) and a Y/C terminal (mini-DIN 4-pin connector). The Y/C (S-video) terminal has priority.

Press this button to activate the picture contrast adjustment mode or picture brightness adjustment mode. Each time you press the button, the adjustment item changes. Picture contrast f Picture brightness

Adjust the value with the VOLUME/SELECT buttons 4. Also used as a control button in the menu function mode.

4 Volume/Select buttons [VOLUME/SELECT � +]
Adjusts the speaker volume. Also used as a control button in the menu function mode.

12 Input C/D (Slot) buttons [INPUT SELECT C/D (SLOT)]
Selects the signals to be input via the input cards installed in the rear panel card slots. C, D: Selects the image from the input card in the slot. For details on input connectors and using the INPUT SELECT button, refer to page 7.

5 Menu button [MENU]
Displays and disappears the <MENU> screen. Pressing the CHROMA/PHASE button 2 with the Menu button depressed will display the <SET-UP MENU> screen.

13 Power indicator
Unlit : The main power is OFF. Orange : The main power is ON, but the monitor�s power is OFF (in the stand-by mode). Green : The main power is ON, and the monitor�s power is ON (in the normal operation mode).

6 Under Scan button [UNDER SCAN]
Reduces the screen size to display the entire image. Press the button again to cancel Under Scan. When selected, the Under Scan button lights.

14 Power switch [POWER

]

7

Color Off button [COLOR OFF]
Cuts color signals to display a black and white image. Press the button again to restore the original color. When selected, the COLOR OFF button lights. Note: � This function is invalid with RGB input.

Press the power switch to turn the monitor�s power ON or OFF when the main power is ON. Note: � When RUSH DELAY is set to SLOW, it takes about three seconds before power is actually supplied after the power switch is pressed.

15 Speaker
A built-in speaker is located inside the right side panel when the monitor is viewed from the front.

4
1-4 No.51961