|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Exactly what was needed to assess the product - excellent value and great service
;
Nice to have the service manual for the Sony DCR-TRV345E now. The document is of excellent quality.
;
MACKIE HR824 26 pages English-only Service Manual contains:
1) HR824 technical overview with the description of front and rear panel switches.
2) HR824 specs
3) Block Diagram
4) Wiring Diagram
5) Packaging management
6) Spare part & final assembly list (for PCB rev A and B) + exploded view
7) Test Procedures (where, how to measure voltage...) including Test Point diagram on the PCB.
8) IC and Transistor charts.
Excellent guide: very clear, good scan quality enabling us to print readable diagram :-)
Note:
Mackie HR824 make extensive use of surface mount devices (SMD). Service on the HR824 must
only be undertaken by experienced service technicians with the right tools, experience and patience to perform surface mount rework when needed.
;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
IC, TB31224F
Pin No. 1 2 Pin Name TX-IN VCC3 I/O I � Description Input terminal of TX VCO oscillation signal. Power supply terminal. LOCAL OSCILLATOR input and output terminals. Colpitts oscillator is formed by 3, 4 LO-1, LO-2 O internal emitter follower and external X�tal. And external injection is possible from pin 3. 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 SIG OUT CLK DATA STB FIL-OUT FIL-IN COMP-OUT C-NF MIC-OUT MIC-IN PRE-IN PRE-OUT EXP-OUT RECE-IN RO1 RO2 O I I I O I O � O I I O O I O O Output terminal of detection signal. It is the open drain output. Input terminal of clock. Input terminal of serial data. Input terminal of strobe signal. Output of FILTER AMP. Input of FILTER AMP. Output of COMPRESSOR. Feedback circuit of T type is formed by external capacitor with SUM AMP. Output of MIC AMP and connected directly to input of SUM AMP. Input terminal of MIC AMP. Inverted input of PRE AMP. Output of PRE AMP. Connected directly to EXPANDER. Output of SUM AMP at EXPANDER. The signal from gain cell is gained by inverted amp. Inverted input of RECEIVER AMP. Receiving output for a dynamic receiver. Used for BTL output type with RO1 terminal when a ceramic receiver is used. BATTERY ALARM terminals. When VCC decrease VBAT-L, This terminal outputs 21 BAT-ALM O �H� level. Detection voltage is controlled by data bit. This terminal is open collector output. 22 23 24 25 26 27 28 29 30 31 32 33 34 RSS1 DATA-OUT D-COMP-IN N FIL-IN N FIL-OUT AF-OUT QUAD IF-OUT GND1 DEC IF-IN VCC1 2ND MIX-OUT O O I I O O I O � I I � O Power supply terminal. MIX output terminal. Output impedance is around 1.5k�. This terminal outputs DC level according to input signal level to IF AMP. Dynamic range is around 70dB. Output terminal for wave form shaping. This terminal is open collector output. DATA COMPARATOR input terminal. This terminal input demodulation signal of DATA. NOISE FILTER input and output terminals. BPF is composed of external capacitors and resistors. Connected internally to rectifier circuit by coupling capacitor. Demodulated signal output terminal. Carrier leak is small as LPF is built-in. Output impedance is around 360�. Phase shift signal input terminal of FM demodulator. Output terminal of IF AMP. GND terminal. 2nd IF input and decoupling for bias. Input impedance is around 1.5k�. Input the serial data for controlling IC.
22
|
|
|
> |
|