|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The purchased manual is an high quality scan of the original Philips paper-based Service Manual. I am very satisfied!
 ;
The purchased manual is an scan of the original Panasonic paper-based Service Manual. Unfortunately the contrast is not perfect, but I am satisfied anyway!
;
The purchased manual is an high-quality scan of the original JVC paper-based Service Manual. The Service Manual includes the Owner´s Manual, so you do not have to buy both of them.
;
It paid to find this Service Manual, couldn't find it anywhere else. Exactly what I wanted. Received within 24 hours.
;
Complete manual with clear schematic diagrams and printed circuit board layouts of two variants of the headset and the transmitter an old and a new version.
Also shows how the headset and the transmitter is opened and how transmitter and receivers can be adjusted and where to measure.
I had no problems to repair the headset using this service manual.
IC, TB31224F
Pin No. 1 2 Pin Name TX-IN VCC3 I/O I � Description Input terminal of TX VCO oscillation signal. Power supply terminal. LOCAL OSCILLATOR input and output terminals. Colpitts oscillator is formed by 3, 4 LO-1, LO-2 O internal emitter follower and external X�tal. And external injection is possible from pin 3. 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 SIG OUT CLK DATA STB FIL-OUT FIL-IN COMP-OUT C-NF MIC-OUT MIC-IN PRE-IN PRE-OUT EXP-OUT RECE-IN RO1 RO2 O I I I O I O � O I I O O I O O Output terminal of detection signal. It is the open drain output. Input terminal of clock. Input terminal of serial data. Input terminal of strobe signal. Output of FILTER AMP. Input of FILTER AMP. Output of COMPRESSOR. Feedback circuit of T type is formed by external capacitor with SUM AMP. Output of MIC AMP and connected directly to input of SUM AMP. Input terminal of MIC AMP. Inverted input of PRE AMP. Output of PRE AMP. Connected directly to EXPANDER. Output of SUM AMP at EXPANDER. The signal from gain cell is gained by inverted amp. Inverted input of RECEIVER AMP. Receiving output for a dynamic receiver. Used for BTL output type with RO1 terminal when a ceramic receiver is used. BATTERY ALARM terminals. When VCC decrease VBAT-L, This terminal outputs 21 BAT-ALM O �H� level. Detection voltage is controlled by data bit. This terminal is open collector output. 22 23 24 25 26 27 28 29 30 31 32 33 34 RSS1 DATA-OUT D-COMP-IN N FIL-IN N FIL-OUT AF-OUT QUAD IF-OUT GND1 DEC IF-IN VCC1 2ND MIX-OUT O O I I O O I O � I I � O Power supply terminal. MIX output terminal. Output impedance is around 1.5k�. This terminal outputs DC level according to input signal level to IF AMP. Dynamic range is around 70dB. Output terminal for wave form shaping. This terminal is open collector output. DATA COMPARATOR input terminal. This terminal input demodulation signal of DATA. NOISE FILTER input and output terminals. BPF is composed of external capacitors and resistors. Connected internally to rectifier circuit by coupling capacitor. Demodulated signal output terminal. Carrier leak is small as LPF is built-in. Output impedance is around 360�. Phase shift signal input terminal of FM demodulator. Output terminal of IF AMP. GND terminal. 2nd IF input and decoupling for bias. Input impedance is around 1.5k�. Input the serial data for controlling IC.
22
|
|
|
> |
|
