|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Exactly what was needed to assess the product - excellent value and great service
 ;
Nice to have the service manual for the Sony DCR-TRV345E now. The document is of excellent quality.
;
MACKIE HR824 26 pages English-only Service Manual contains:
1) HR824 technical overview with the description of front and rear panel switches.
2) HR824 specs
3) Block Diagram
4) Wiring Diagram
5) Packaging management
6) Spare part & final assembly list (for PCB rev A and B) + exploded view
7) Test Procedures (where, how to measure voltage...) including Test Point diagram on the PCB.
8) IC and Transistor charts.
Excellent guide: very clear, good scan quality enabling us to print readable diagram :-)
Note:
Mackie HR824 make extensive use of surface mount devices (SMD). Service on the HR824 must
only be undertaken by experienced service technicians with the right tools, experience and patience to perform surface mount rework when needed.
;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
Alignment and Adjustments
3-3-2 Automatic Degaussing
A degaussing coil is mounted around the picture tube, so external degaussing after moving the TV should be unnecessary. However, the receiver must be properly degaussed upon installation. The degaussing coil operates for about 1 second after the power is switched ON. If the set has been moved or turned in a different direction, disconnect its AC power for at least 10 Minutes. If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before removing power.
3-3-4 FOCUS Adjustment
1. Input a black and white signal. 2. Adjust the tuning control for the clearest picture. 3. Adjust the FOCUS control for well defined scanning lines in the center area of the screen.
3-3-5 B+ Line Check
There are 3 power modes : 1. �A� : When AC power supply is connected ; � Stand-By� mode. 2. �B� : When � Set Power-ON� button is pressed. 3. �C� : Driven by FBT. Each voltage is marked on its lead-in wire. ( )
3-3-3 High Voltage Check
CAUTION : There is no high voltage adjustment on this chassis. The B+ power supply must be set to either +135V or +125V (for 20� screen). Conditions : Full color bar input and normal picture level. 1. Connect a digital voltmeter to the second anode of the picture tube. 2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. The high voltage must not exceed 29.5KV. 4. Adjust the Brightness and Contrast controls to both extremes. Ensure that the high voltage does not exceed 29.5KV under any conditions. SIZE MAX H-VOLTAGE 27.5KV 29.5KV 29.5KV 29.5KV 21�± 1 25� 29� 29�± 1
3-3-6 F/S (Fail Safe) Circuit Check
1. The failsafe circuit check is the final step after servicing. 2. Turn the power switch on and adjust the screen for �Normal�. 3. Temporarily short Pin R and Pin X on the chassis (RX05, RX04). Sound and picture will disappear. 4. The TV should remain in this state. This shows that the failsafe circuit is working properly. 5. To restore picture and sound, temporarily turn off the AC power supply. After about 30 seconds, switch power ON.
3-6
Samsung Electronics
|
|
|
> |
|
