|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Genuine Toshiba owner's manual. Couldn't really ask for more. And written in understandable English in contrast to a few recent experiences I have had with manuals for other equipment other than Toshiba but made in China and written in "Chinglish"!
;
I purchased a vintage Sony mixer off eBay and within the hour was able to locate and purchase the manual for it.I mean really,where else can you find a manual for a product made in 1983!? It was easy to find and purchase/download the manual I needed.I will use this site again for other equipment I have! Great site!
;
manual de usuario perfecto y completo de buena calidad de impresion y muy detallado ideal !
 ;
It`s full copy of a service manual from url http://www.philips.owner-manuals.com/PM3216-service-manual-PHILIPS.html
;
perfect! you just sent to me the copy in Italian witout even my specification!!!! so you are really smart cooperative and efficient. To my opinion the best place all over to get a manual of electronics!!!!
TX-SR502_En.book Page 48 Friday, March 12, 2004 1:05 PM
Advanced Setup
Crossover Frequency
Advanced setup cannot be set while headphones are connected, Speaker B is on, or the multi channel input is being used.
4
To get the best bass performance from your speaker system, you need to set the crossover frequency according to the size and frequency response of your subwoofer and other speakers (front, center, and surround).
Press the [SETUP] button. Setup closes.
1
AMP
Press the [AMP] button followed by the [SETUP] button on the remote controller.
Note: � For a more accurate setting, look up the frequency response in the manuals supplied with your speakers and set accordingly. In addition, listen to some music that you know well and choose a higher crossover frequency if you think there�s not enough sound coming from the subwoofer; a lower setting if you think there�s too much.
2
ENTER
Use the Up and Down [ ]/[ ] buttons to select �1. SP Con�g,� and then press the [ENTER] button.
Speaker Distance
To get the best from surround sound, it�s important that the sound from each speaker reaches the listener at the same time. To achieve this, you need to specify the distance from each speaker to the listening position.
ENTER
1
Use the Down [ ] button to select �Crossover,� and then use the Left and Right [ ]/[ ] buttons to select a crossover frequency. Choose a crossover frequency suitable for your setup. If you�re using a subwoofer, choose a crossover frequency based on the diameter of your front speakers. If you�re not using a subwoofer, use the diameter of the �rst speaker that you speci�ed as Small in steps 4 through 7 in the �Speaker con�guration� setting.
Speaker cone diameter Over 8 in. (20 cm) 6-1/2 to 8 in. (16�20 cm) 5-1/4 to 6-1/2 in. (13�16 cm) 3-1/2 to 5-1/4 in. (9�13 cm) Under 3-1/2 in. (9 cm) Crossover frequency 60Hz 80Hz
DISPLAY
Measure and make a note of the distance from each speaker to the listening position.
AMP
3
ENTER
2
Press the [AMP] button followed by the [SETUP] button on the remote controller.
ENTER
3
ENTER
Use the Up and Down [ ]/[ ] buttons to select �2. SP Distance,� and then press the [ENTER] button.
ENTER
4
Use the [DISPLAY] button to switch ft or m. ft: distances in feet. Can be set from 1 to 30 feet in 1-foot steps. m: distances in meters. Can be set from 0.3 to 9 meters in 0.3-meter steps.
100Hz (default) 120Hz 150Hz
48
|
|
|
> |
|
