|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I found my Clarion VRX8370R in the Camper I bought and I wasn't able for month to understand it.
The Owner Manual was perfect and just what I was searching for.
Thank you.
Leonardo
;
Very good copy of Manual, clear and easy to print off, arrived very promptly and reasonably priced.
Thanks, I will use you again.
;
Zeer duidelijke afdrukken op A4-formaat , zeer uitgebreide handleiding . Pluspunt ,zeer snelle
respons van jullie , binnen de 24h . Top !!!
;
I AM HIGHLY IMPRESSED BY THE EASE OF USE OF THIS DOWNLOAD SERVICE. INSTRUCTIONS ARE CLEAR AND SIMPLE TO FOLLOW....EVEN BY TECHNOPHOBES SUCH AS MYSELF. THE EMAILS POINT YOU IN THE RIGHT DIRECTION...ITS SO EASY PEASY. THE DOWNLOAD CHOICE OF USER MANUALS IS EXTENSIVE AND I COULD NOT FIND A CHEAPER OR MORE EFFICIENT SERVICE ON THE INTERNET. I COULD NOT HAVE MADE A BETTER CHOICE OF INFORMATION PROVIDER. SHOULD I EVER NEED ANOTHER USER MANUAL, THEN THIS IS THE FIRST CHOICE SITE. COULD NOT BE BETTER PLEASED!!!!!!!...MANY THANXES FROM JIM BURNS
;
I was impressed with the quality of service (frequent e-mails to let you know the status of your order), and the speed at which the download became available. The manual was a life saver and was not easy to track down. Thank you for such an excellent service.
Common Operations
Setting the Clock
Before operating the unit any further, first set the unit�s clock. When you plug the AC power cord into the wall outlet, �0:00� starts flashing on the display. You can set the clock whether the unit is on or off. � There is a time limit in doing the following steps. If the setting is canceled before you finish, start over from step 1. � For UX-J50 only, you can also use CLOCK/TIMER on the unit for this operation.
To change the clock
1 Make sure the (timer) indicator is not lit on the display. � If it is lit, press and hold CLOCK/TIMER until it goes off. 2 Press CLOCK/TIMER repeatedly until the unit enters the clock setting mode (the hour digits start flashing on the display). First time you press CLOCK/TIMER, the unit enters the timer setting mode. (See page 20.) 3 Repeat steps 2 and 3 of the procedure of �Setting the Clock.� 4 Press and hold CLOCK/TIMER again so that the (timer) indicator goes off.
1
Press CLOCK/TIMER.
The hour digits start flashing on the display.
CLOCK /TIMER
2
Press UP or DOWN to adjust the hour, then press CLOCK/TIMER.
The minute digits start flashing.
UP
CLOCK /TIMER
Turning On the Power
To turn on the unit, press STANDBY/ON STANDBY/ON . The STANDBY/ON lamp lights green and �HELLO� appears on the display. � When you press the source button�CD 3/8, TAPE 2 3, FM/AM, and AUX, the unit automatically turns on and starts playback if the source is ready. To turn off the unit (standby), press STANDBY/ON again. The STANDBY/ON lamp lights red and �GOOD BYE� appears on the display. � �0:00� flashes on the display until you set the built-in clock. After setting the clock, the clock time will appear on the display while the unit is on standby. The illumination and display brighten only for 4 seconds by pressing DIMMER. � A little power is always consumed even while the unit is on standby. To switch off the power supply completely, unplug the AC power cord from the AC outlet.
When you unplug the AC power cord or if a power failure occurs The clock is reset to �0:00� right away, while the tuner preset stations (see page 12) will be erased in a few days.
DOWN
3
Press UP or DOWN to adjust the minute, then press CLOCK/TIMER.
To check the clock time during play
On the remote control ONLY: Press DISPLAY (gray-colored). � Each time you press the button, the source indication and the clock time alternate on the display.
DISPLAY
� When you unplug the AC power cord or if a power failure occurs The clock is reset to �0:00� right away. If this happens, set the clock again. � The clock may gain or lose 1 to 2 minutes per month If this happens, reset the clock.
9
|
|
|
> |
|
