TOSHIBA V241EW
Owner's Manual

Toshiba 2-7
Presetting the Stations Automatically
You do not need to preset the stations if you have already set them automatically (see Plug & Auto Set Up on page 12). Your VCR contains a built-in tuner used to receive television broadcasts. You must preset the stations received through the tuner. This can be done: x Plug & Auto Set up (see page 12) x Automatically x Manually (see page 18)

Presetting the Stations Manually
GB GB

�

� �
PROG OPTIONS INSTALL INSTALL

You do not need to preset the stations manually if you have already set them automatically. To enable the VCR to decode a scrambled TV station, the decoder must be switched on.

1

PROG

OPTIONS

INSTALL INSTALL CLOCK BONUS LANG

Press the MENU button on the remote control. Result: The programming menu is displayed. Press the corresponding �, � or ¥, � buttons to select the INSTALLATION option. Press the OK button to select this option. Result: The INSTALLATION menu is displayed. Press the � or � buttons to select MANUAL SET UP option. Press the � button to select this option. Result: The TV STATION TABLE menu is displayed. Press the � or � buttons to select a programme number as required. Press the � button to preset the station. Result: The MANUAL TUNING menu is displayed. Press the ¥ or � buttons to start scanning. Result: The frequency band is scanned and the first station found is displayed. If you know the number of the channel you want, press the numeric buttons on the remote control for example, for channel E21, first press �0� and then press �2�, �1� (see page 40). Press the � button, until the DECODER is selected. Press the � button to activate or deactivate use of the decoder for the TV station, if necessary. Press the � or � buttons until the NAME is selected. The station name is set automatically from the broadcast signal. To change the programme�s name, press the � button. Result: The first letter of the name flashes. To... Select a character in the name Move to the next or previous character Then... Press the � or � button until the required character is displayed (letters, numbers or �-� character). Press the � or ¥ buttons respectively. Then...
x x x

CLOCK

BONUS

LANG

INSTALLATION END: MENU

2 3
END: MENU

You can store up to 80 stations.

INSTALLATION OK
� �

�
1 2 3 4

To enable the VCR to decode a scrambled TV station, the decoder must be activated after the scan (see pages 18).

¥� OK

� �

¥�

4 5
INSTALL

Press the MENU button on the remote control. Result: The programming menu is displayed. Press the corresponding �,� or ¥, � buttons to select the
INSTALL

INSTALLATION option.
Press the OK button to select this option. Result: The INSTALLATION menu is displayed. Press the corresponding � or � buttons, until the AUTO SET UP option is selected. And then press the � button to select this option. Result: The country selection MENU is displayed. Press the � or � buttons to select your country. The VCR searches for the stations according to a preset preference list corresponding to the country that you have selected.

AUTO SET UP MANUAL SET UP TV SYSTEM VCR OUTPUT CH

:G :CH60

AUTO SET UP MANUAL SET UP TV SYSTEM VCR OUTPUT CH

6
:G :CH60

7 8

� � � �

�

END: MENU

�

END: MENU

5

** TV STATION TABLE ** COUNTRY SELECTION BELGIQUE �STERREICH DENMARK DEUTSCHLAND ESPA�A FINLAND ITALIA NETHERLANDS NORGE SCHWEIZ SVERIGE
� �

�
6

Press OK button. Result: A message appears, indicating that any channels already preset on your VCR will be deleted. Press OK to start the auto scanning. Result: x The PLEASE WAIT indication flashes on the television screen. x The first frequency band is scanned and the first station found is displayed and stored. x The VCR then searches for the second station and so on. x When the automatic scanning procedure has finished, the VCR switches automatically to programme 1. � The number of stations automatically stored by the VCR depends on the number of stations that it has found. (country, reception conditions, etc.) If you wish to cancel the auto scanning before the end, press the MENU button three times to exit the menu. x The time and date are set automatically from the broadcast signal. If the signal is weak or ghosting occurs, the time and date may not be set automatically. In this case, they should be set manually (see page 14). Once the auto scanning procedure has finished, some stations may have been stored more than once; select the stations with the best reception and delete the ones no longer required (see page 19).

PR 1 2 3 4 5
� �

004 CH

NAME ----

DEC OFF

9 10 11

7

¥�

PORTUGAL OTHER EXECUTE:OK

SWAPPING:OK DELETE:CLR/RST MENU

�

12 13

** MANUAL TUNING ** PR CH MFT DECODER NAME
� �

YOUR DATA WILL BE LOST PRESS OK TO CONTINUE MENU TO EXIT

:1 : 004 :: OFF : ---MEMORY: OK END: MENU

¥�

14

If you... Wish to store the station displayed

8

Press the corresponding � or � buttons, until the MFT is selected. Press the ¥ or � buttons to adjust the picture, if necessary. Press OK to store the station . Press the corresponding � or � buttons, until the CH is selected. Press the ¥ or � buttons to go on scanning the frequency band and display the next station Go back to the beginning of Step 14

�

AUTO SET UP PLEASE WAIT 30% Is s s s s s s s s s s s -------I END:MENU

Do not wish to store the station displayed

x x x

15 16

Repeat this procedure from Step 6 onwards, until all the required

x

Reference Information

stations have been stored. On completion, press the MENU button three times to exit the menu.

17

18