|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Dear Sirs,
Thank you for the fast support, the manual does provide all necessary information to repair the radio. All schematics are in a good quality for reading.
The manual fits 100% to my requirements as a technican.
Kind regards Thomas
;
the big video recorder format s-vhs many features delicate in loading system of the cassette. Such machines are no longer manufactured, it would be too expensive.
 ;
THIS MANUAL IS VERY GOOD AND VERY CLEAR
PLEASE NOTE IT DOES NOT CONTAIN THE SETUP INFORMATION TO ALIGHN THE GEARS IN THE CD MECH IT DOES SHOW ALL THE PARTS AND THEIR LOCATIONS .
;
Complete service and operation manual. All schematics are there, all circuit boards AND add-on boards. Including exploded views ,component names and specifications. Also electrical and mechanical adjustment procedures are in this manual. This manual also covers the more advanced BR-S811E unit. Scan quality is fair and usable.
;
High quality scan of original Service Manual. Everything´s fine!
VC-AA350A/L/M/W VC-AA352W,AA360A,AA370A VC-AA550A/L/W,AA560A,AA570A Note: Whenever replacing the reel disk, perform the height checking and adjustment.
Master plane Reel disk height adjusting jig
Notes: 1. Hold the torque gauge by hand so that it is not moved. 2. Do not keep the reel disk in lock state. Do not allow longtime measurement.
10 ± 0.2mm
Reel disk
A
Mechanism chassis
4-7 CHECKING AND ADJUSTMENT OF TAKEUP TORQUE IN REWIND MODE
� Remove the cassette housing control assembly. � After short-circuiting between TP803 and TP802 provided at main PWB, plug in the power cord. � Setting 1. Set a torque gauge to zero on the scale. Place it on the supply reel disk. 2. Press the rewind button. 3. To calculate the remaining capacity, slowly rotate the take-up reel disk, and then shift it into the rewind mode. � Checking 1. Turn the torque gauge slowly (one rotation every 2 to 3 seconds) by hand in the CCW direction. 2. Make sure that the indication of torque gauge is not less than 30mN·m (306gf·cm).
Torque gauge
B
Reel disk
Figure 4-5.
4-6 CHECKING AND ADJUSTMENT OF TAKEUP TORQUE IN FAST FORWARD MODE
� Remove the cassette housing control assembly. � After short-circuiting between TP803 and TP802 provided at main PWB, plug in the power cord. � Setting 1. Set a torque gauge to zero on the scale. Place it on the take-up reel disk. 2. Press the FF button. 3. To calculate the remaining capacity of the play back mode, slowly rotate the supply reel disk, and then shift it into the forward mode. � Checking 1. Turn the torque gauge slowly (one rotation every 2 to 3 seconds) by hand in the CW direction. 2. Make sure that the indication of torque gauge is not less than 30mN·m (306gf·cm).
Torque gauge
CCW
30mN·m (306gf·cm) or more
30 The gauge is held at its maximum value. (Red mark)
Supply reel disk 30mN·m (306gf·cm) or more CW
The gauge is held at its maximum value. (Red mark)
Idler ass'y
Figure 4-7. � Adjustment 1. If the rewind winding-up torque is less than the specified value, clean the capstan D.D. pulley, reel belt, and limiter pulley with cleaning liquid, rewind again, and check the winding-up torque. 2. If the winding-up torque is still out of range, replace the drive belt.
Idler ass'y
Figure 4-6. � Adjustment 1. If the FF winding-up torque is less than the specified value, clean the capstan D.D. pulley, reel belt, and limiter pulley with cleaning liquid, and check again. 2. If the torque is less than the set value, replace the reel belt.
12
|
|
|
> |
|
