|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It is perfect, exactly what we needed. It's like the paper version but less clutter.
 ;
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
BASIC OPERATION
HOW TO SET A DELAYED RECORDING
8. Enter the start time using the [
/ ] or the NUMBER BUTTONS hours first then minutes (when entering less than 10 minutes add a '0' before the number), for example for 21:05 start, press 2 1 0 5. Then press SET to confirm.
DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D0 3 2 1 : 0 5 -:---/-- --:--:---/-- --:--:--
1/2 SP * SP * -----
9. Enter the stop time, for example for 22:30 stop,
press 2 2 3 0.
10. If you wish to change the RECORDING
SPEED, use the [ / ] to highlight SP. Press [ / ] to select standard play (SP), long play (LP) or extended play (EP) as required.
11. [See NOTE below]. For VPS/PDC setting use
the [ / ] to highlight the final column. Using the [ / ] will select VPS/PDC ON or OFF ( * = ON - = OFF).
DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D0 3 2 1 : 0 5 2 2 : 3 0 --/-- --:--:---/-- --:--:--
1/2 SP * LP * -----
12. Press SET to confirm.
� The MENU now shows all the timer settings you have entered. If you wish to make additional timer recordings, repeat this procedure. settings, press MENU to remove the menu from the TV screen.
13. When you have completed entering timer
DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7 D 0 3 2 1 : 0 5 22 : 3 0 --/-- --:--:---/-- --:--:-1/2 SP * LP -----
14. Ensure that the tape on which you wish to
record is inserted into the VCR, then press
TIMER ON/OFF once to place the VCR in
TIMER POWERSAVE/TIMER STANDBY mode. will be shown on the display.
NOTES:
� It is essential that the start time as it appears in the TV listing is used to program the VCR, as this information is used to identify the VPS/PDC signal corresponding to your programme. VPS/PDC is a signal broadcast by some TV stations which adjusts the start and stop time of your VCR recording. This ensures that if there is a change in broadcast time for your programme the VCR will still record the whole programme. If flashes a video tape has not been inserted into the VCR. If the video tape is ejected when the VCR tries to record the record protection tab has been removed. During recording, press STOP ( ) to cancel the recording. If there are further recordings to be made, the VCR will return to TIMER POWERSAVE/TIMER STANDBY. If problems persist contact the SHARP Helpline on tel: 08705-274277 (office hours) or www.sharp.co.uk/support
18
�
� � �
|
|
|
> |
|
